Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 181

Страница: 181 / 215

NO TICE

– When pushing the display module leftwards or rightwards, pay attention to

the buckles on the panel to prevent damage to the display module.

– The gasket is used to adjust the distance between the display module and

the door panel.

– The gasket dimensions are 25 mm (L) x 12 mm (W) x 2 mm (H) and the

center aperture is 6 mm.

Figure 6-21 Replacing a display module (NetCol5000-C065)

Figure 6-22 Replacing a display module (NetCol5000-C030/C032)

4. Install the new display module in the original position on the front door by

performing the preceding steps in reverse order.

5. Connect the control signal cables to the display module. Close and lock the

front door.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

173

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды