Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 182

Страница: 182 / 215

CA UTION

● If the main control board is not powered off, after the DP cable is inserted into

the display module, the main control board detects and initializes the display

module. This process takes 10s to 30s. Wait for 5s to 10s. The indicator on the

panel turns on, but the screen does not turn on. Wait for another 5s to 20s

until the screen is restored to the state before the replacement.

● If the main control board is powered off, power on the main control board after

the DP cable is connected to the display module. After the main control board

is powered on, the startup logo and self-check progress bar are displayed on

the display module. The main screen is displayed. The whole restoration takes

about 60s to 90s.

Step 3 (Optional) Import the configuration. If the web or ECC is not configured, skip its

step.
1. Insert the USB flash drive into the main control board or main control

module. Choose Maint > USB Operations > Import Config as an admin user

to import the back up data in the USB flash drive.

2. Log in to the WebUI of the smart cooling product as an administrator user.

Choose Maintenance > Configuration, and choose the backup data. After

(optional) tapping Configuration File Encryption Password, tap Upload to

import the backup data from the computer.

----End

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

174

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды