Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 163

Страница: 163 / 215

Symptom

Possible Causes

Troubleshooting

No water is

supplied to the

water inlet

solenoid valve of

the humidifier.

1. The upstream water

supply is faulty or the

water pressure is

below the lower

threshold.

2. The water inlet

solenoid valve is

blocked or faulty.

3. The cable to the

water inlet solenoid

valve is incorrectly

connected.

1. Restore the water supply.
2. Replace the water inlet

solenoid valve.

3. Reconnect the cable.

6.4 Parts Replacement

6.4.1 Replacement Requirements

NO TICE

● Before removing or installing the power cable, turn off the power switch.
● Before connecting a power cable, check that the label on the power cable is

correct.

● During the installation of AC power supply facilities, follow the local safety

regulations.

● When operating the high-voltage and AC-powered facilities, use dedicated

tools.

● Ensure that a spare component is the same model as the faulty one is prepared

before replacing the faulty component.

● Do not install or remove power cables when the device is on. Transient contact

between the core of the power cable and the conductor may generate electric

arcs or sparks, which may cause fire or hurt eyes.

● Before removing cables from a faulty component, mark the cables with their

corresponding ports numbers for later connection (confirm by referring to the

electrical conceptual diagram).

● Ensure that the cables are connected to the spare component properly.

6.4.2 Replacing an Air Filter

Prerequisites

●

An air filter needs to be replaced.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

155

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды