Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 171

Страница: 171 / 215

Figure 6-10 Removing a T/H sensor (NetCol5000-C030/C032)

Step 5 Install the new T/H sensor at the original position, and connect the cable

terminals to the T/H sensor.

NO TE

Before installing the new T/H sensor, ensure that its DIP switch setting is consistent with

that on the original T/H sensor. That is, the first toggle switch is ON, and the others are

OFF.

Step 6 Install the air filter. Close and lock the rear door, tap Start on the home screen of

the display module.

----End

6.4.7 Replacing a Supply Air Temperature Sensor

Prerequisites

●

A supply air temperature sensor needs to be replaced.

●

A spare temperature sensor of the same model is available and functional.

Context

Temperature sensors can be replaced with power-on.

Recommended tools: diagonal pliers, cable tie, Phillips screwdriver

Preparation: Maintain from the front door.

Procedure

Step 1 Tap Shutdown on the home screen of the display module.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

6 System Operation and Maintenance

Issue 04 (2021-03-15)

163

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды