Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 96

Страница: 96 / 215

Menu

Parameter

Description

Setting Rule

Humidifying

function

The humidifying

function can be set to

Enable, Disable, or

Enabled when active

power.

Enable indicates that the

electric humidifier will be

started when the ambient

humidity is lower than the

certain humidity range of

the humidity set point.

Disable indicates that the

electric humidifier will not

be started. Enabled when

active power indicates

that the electric humidifier

will be started when the

main power is active and

the ambient humidity is

lower than the certain

humidity range of the

humidity set point.

Dehumidifying

function

The dehumidifying

function can be set to

Enable, Disable, or

Enabled when active

power.

Enable indicates that the

dehumidification function

will be enabled when the

ambient humidity exceeds

the certain humidity range

of the humidity set point.

Disable indicates that the

dehumidification function

will not be enabled.

Enabled when active

power indicates that the

dehumidification function

will be enabled when the

main power is active and

the ambient humidity

exceeds the certain

humidity range of the

humidity set point.

Floor water

overflow alarm

action

Set this parameter to

Shutdown,

Inactivity, Only

indoor fan running,

or Humidifier

stopped based on

site requirements.

Retain the default value.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

4 Power-On Commissioning

Issue 04 (2021-03-15)

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды