Huawei NetCol5000-C030 Series Скачать руководство пользователя страница 73

Страница: 73 / 215

Procedure

Step 1 Ensure that the needle valve and exhaust valve on the pipe are closed and the

chilled water valve is in the 100% state, as shown in

Figure 3-45

Figure 3-45 Adjusting the chilled water valve

Step 2 Open the main water inlet valve.

Step 3 Gradually open the exhaust valve, as shown in

Figure 3-19

Figure 3-20

. Air and

chilled water flow out of the exhaust hose together.

Step 4 Adjust the air exhausting speed until no bubble flows out of the hose.

Step 5 After air is expelled, manually turn the chilled water valve to the 0 state.

Step 6 Close the exhaust valve.

----End

3.11 (Optional) Leakage Test with Water

NO TICE

● If the leakage test has been done with nitrogen, skip the test with water.
● Ensure that the indoor temperature is always above 0°C during the leakage test

with water, otherwise, the pipes may experience frost cracks. If the indoor

temperature is below 0°C, take anti-freezing measures for the pipes.

Manually open the chilled water valve. Inject water to 0.8 MPa, and preserve the

pressure for 24 hours. Then connect a pressure gauge to a needle valve on the

pipeline to measure the pressure. If the reading remains unchanged, the pipe is

not leaking. You can perform the following operations.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Содержание NetCol5000-C030 Series
























































































































































































































Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030 Series, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030 Series

Отзывы:

Похожие инструкции для NetCol5000-C030 Series

Бренды по названию

Популярные бренды