manualshive.com logo in svg

HTP MODCON1000, Установка, Запуск, Обслуживание, Запчасти, Гарантия

HTP MODCON1000 - высококачественный продукт для отопления. Данный газовый котел обеспечивает максимальный комфорт и экономичность. Установка, запуск и обслуживание легко выполняются с помощью бесплатного руководства по эксплуатации, доступного для загрузки на manualshive.com. Гарантия и запчасти также включены.

Поделиться
Скачать
background image

39 

 

 

                                                                                     LP- 428 REV. 9.2.14 

D. CHECK INLET GAS PRESSURE 

The gas valve is equipped with an inlet gas pressure tap that can be used to measure the gas pressure to the unit. To check gas 
pressure, perform the steps listed below: 
 
1. 

IMPORTANT! 

Before you connect to the inlet pressure, shut off the gas and electrical power to unit. 

 
2. Loosen the pressure tap with a small screwdriver. Refer to Figs. 20 and 21 for locations. 
 
3. Each unit is equipped with a needle valve that will accept a 5/16 ID hose to connect to a digital manometer or liquid gauge to 
measure incoming pressure from 0-

35” w.c. 

 
4. Turn on the gas and power up the unit. 
 
5. Put the unit into manual service mode (details on service mode are in the back of this manual). In service mode, monitor pressure to 
assure it does not drop below 1 inch from its idle reading. If gas pressure is out of range, or pressure drop is excessive, contact the gas 
utility, gas supplier, qualified installer, or service agency to determine the correct action needed to provide proper gas pressure to the 
unit. If gas pressure is within normal range, proceed to Step 6. 
 
6. Exit Service mode, then turn power off and shut off the gas supply at the manual gas valve before disconnecting the hose from the 
gas monitoring device. Tighten the screw on the pressure tap, turn gas on, and check for leaks with a soapy solution. If a leak is 
present, bubbles will appear on the pipe. 
 

 

Ensure the pressure tap screw is properly tightened to prevent gas leaks. Failure to do so could cause substantial property damage, 
severe personal injury, or death. 
 
The gas piping must be sized for the proper flow and length of pipe to avoid pressure drop. The gas meter and regulator must be 
properly sized for the total gas load. If you experience a pressure drop greater than 1" w.c. (.87 kPa), the meter, regulator or gas line 
may be undersized or in need of service. You can attach a manometer to the incoming gas drip leg after removing the cap. The gas 
pressure must remain between 3.5" (.87 kPa) and 14" (3.5 kPa) during stand-by (static) mode and while in operating (dynamic) mode. 
 

If an in-line regulator is used, it must be a minimum of 10 feet from the boiler. It is very important that the gas line is properly 
purged by the gas supplier or utility. Failure to properly purge the lines, or improper line sizing, will result in ignition failure.

 

This problem is especially noticeable in NEW LP installations and empty tank situations. This situation can also occur when a utility 
company shuts off service to an area to provide maintenance to their lines. This gas valve must not be replaced with a conventional gas 
valve under any circumstances. 
 

 

DO NOT adjust or attempt to measure gas valve outlet pressure. The gas valve is factory-set for the correct outlet pressure and 
requires no field adjustment. Attempts by the installer to adjust or measure the gas valve outlet pressure could result in damage to the 
valve and cause substantial property damage, severe personal injury, or death. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание MODCON1000


















































































Отзывы:

Нет отзывов

Похожие инструкции для MODCON1000

M&G DuraVent DIS Installation Instructions Manual preview
DuraVent DIS
Бренд: M&G Страницы: 41
Ravelli Pompeii Owners & Installation Manual preview
Pompeii
Бренд: Ravelli Страницы: 53
DeDietrich Twineo EGC 25 User Manual preview
Twineo EGC 25
Бренд: DeDietrich Страницы: 40
Kordi Kordi-10S Manual preview
Kordi-10S
Бренд: Kordi Страницы: 20
geminox THI 2-17 B 120 Technical Instructions preview
THI 2-17 B 120
Бренд: geminox Страницы: 24
Kalvis K-2-16 User'S Installation And Operation Manual preview
K-2-16
Бренд: Kalvis Страницы: 12
Worcester GREENSTAR UTILITY Instruction Manual preview
GREENSTAR UTILITY
Бренд: Worcester Страницы: 64
Ikon IRB-12 Installation & Operation Manual preview
IRB-12
Бренд: Ikon Страницы: 16
U.S. Boiler Company MPO - IQ Service Instructions Manual preview
MPO - IQ
Бренд: U.S. Boiler Company Страницы: 92
Alde Compact 3020 HE Amendment To Installation Instructions preview
Compact 3020 HE
Бренд: Alde Страницы: 4
Viessmann Vitomax HS M73 Operating And Service Instructions preview
Vitomax HS M73
Бренд: Viessmann Страницы: 64
Vaillant ECOTEC PLUS VU 80 Installation And Maintenance Instructions Manual preview
ECOTEC PLUS VU 80
Бренд: Vaillant Страницы: 76
Camus Hydronics DynaFlame Series Installation And Service Manual preview
DynaFlame Series
Бренд: Camus Hydronics Страницы: 92
Laars NEOTHERM LC User Manual preview
NEOTHERM LC
Бренд: Laars Страницы: 12
Lanair MXB-250 Installation And Operating Instructions Manual preview
MXB-250
Бренд: Lanair Страницы: 44
Slant/Fin SENTINEL Installation And Operating Instructions Manual preview
SENTINEL
Бренд: Slant/Fin Страницы: 20
Arikazan Devron Series Operation, Use And Maintenance Manual preview
Devron Series
Бренд: Arikazan Страницы: 38
E.C.A. Proteus Plus Blue 24 kW Installation And Operating Instructions Manual preview
Proteus Plus Blue 24 kW
Бренд: E.C.A. Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды