manualshive.com logo in svg

HTP MODCON1000, Установка, Запуск, Обслуживание, Запчасти, Гарантия

HTP MODCON1000 - высококачественный продукт для отопления. Данный газовый котел обеспечивает максимальный комфорт и экономичность. Установка, запуск и обслуживание легко выполняются с помощью бесплатного руководства по эксплуатации, доступного для загрузки на manualshive.com. Гарантия и запчасти также включены.

Поделиться
Скачать
background image

6 

 

 

                                                                                     LP- 428 REV. 9.2.14 

G. OUTDOOR SENSOR ............................................................................................................................................................... 43

 

H. INDIRECT SENSOR (TOP BOILER CONNECTION) ............................................................................................................... 43

 

I. OPTIONAL 0-10 VOLT BUILDING CONTROL SIGNAL ............................................................................................................ 43

 

J. OPTIONAL HIGH GAS PRESSURE SWITCH .......................................................................................................................... 44

 

K. OPTIONAL LOW GAS PRESSURE SWITCH .......................................................................................................................... 44

 

L. OPTIONAL FLOW SWITCH ...................................................................................................................................................... 44

 

M. OPTIONAL UL353 LOW WATER CUT-OFF INTERFACE KIT ................................................................................................ 44

 

N. WIRING OF THE CASCADE SYSTEM COMMUNICATION BUS ............................................................................................ 45

 

PART 8 

– START-UP PREPARATION...................................................................................................................................... 49

 

A. CHECK / CONTROL WATER CHEMISTRY ............................................................................................................................. 49

 

B. FREEZE PROTECTION (WHEN USED) .................................................................................................................................. 50

 

C. FILL AND TEST WATER SYSTEM .......................................................................................................................................... 50

 

D. PURGE AIR FROM WATER SYSTEM ..................................................................................................................................... 50

 

E. CHECK FOR GAS LEAKS ........................................................................................................................................................ 51

 

F. CHECK THERMOSTAT CIRCUIT(S) ........................................................................................................................................ 51

 

G. CONDENSATE REMOVAL ...................................................................................................................................................... 51

 

H. FINAL CHECKS BEFORE STARTING BOILER ....................................................................................................................... 52

 

I. CASCADE SYSTEM 

– MOD CON 1000 AND 1700 MODELS ................................................................................................... 52

 

PART 9 

– START-UP PROCEDURE ......................................................................................................................................... 53

 

A. CONTROL OVERVIEW ............................................................................................................................................................ 53

 

B. NAVIGATION OF THE DISPLAY .............................................................................................................................................. 53

 

C. OPERATING INSTRUCTIONS ................................................................................................................................................. 54

 

D. PROGRAMMING BOILER SETTINGS ..................................................................................................................................... 54

 

E. PROGRAMMING THE SYSTEM SETTING .............................................................................................................................. 55

 

F. SYSTEM SETTING PROGRAM NAVIGATION......................................................................................................................... 55

 

G. RESETTING THE MAINTENANCE SCHEDULE...................................................................................................................... 57

 

PART 10 

– START-UP PROCEDURES FOR INSTALLER ....................................................................................................... 58

 

A. BOILER CONTROL STATUS MENU ........................................................................................................................................ 58

 

B. BOTTOM BOILER (MASTER) MENU ONLY ............................................................................................................................ 60

 

C. BOILER TEST MODE ............................................................................................................................................................... 60

 

PART 11 

– SHUTDOWN ............................................................................................................................................................ 61

 

A. SHUTDOWN PROCEDURE ..................................................................................................................................................... 61

 

B. VACATION PROCEDURE ........................................................................................................................................................ 61

 

C. FAILURE TO OPERATE ........................................................................................................................................................... 61

 

PART 12 

– TROUBLESHOOTING ............................................................................................................................................ 61

 

A. BOILER ERROR CODE ............................................................................................................................................................ 61

 

B. BOILER ERROR ....................................................................................................................................................................... 61

 

C. BOILER FAULT ........................................................................................................................................................................ 62

 

D. USER INTERFACE DISPLAY .................................................................................................................................................. 62

 

PART 13 

– MAINTENANCE ...................................................................................................................................................... 67

 

A. MAINTENANCE PROCEDURES .............................................................................................................................................. 67

 

Содержание MODCON1000


















































































Отзывы:

Нет отзывов

Похожие инструкции для MODCON1000

Alpha InTec 12S (LPG) Installation And Servicing Instructions preview
InTec 12S (LPG)
Бренд: Alpha Страницы: 44
Joannes Clizia 24 AS Instructions For Use, Installation And Maintenance preview
Clizia 24 AS
Бренд: Joannes Страницы: 44
Bosch 100 EBP Installation And Operating Instructions Manual preview
100 EBP
Бренд: Bosch Страницы: 308
Nature's Comfort AAA Outdoor Boiler Installation And Operating Instructions Manual preview
AAA Outdoor Boiler
Бренд: Nature's Comfort Страницы: 24
Nature's Comfort NCB-120 Installation And Operation Instructions Manual preview
NCB-120
Бренд: Nature's Comfort Страницы: 25
Ferroli ARENA 30 A Installation And Operating Instructions Manual preview
ARENA 30 A
Бренд: Ferroli Страницы: 44
Baxi Megaflo System 24 HE IE LPG Installation & Servicing Instructions Manual preview
Megaflo System 24 HE IE LPG
Бренд: Baxi Страницы: 56
Baxi luna platinum+ Instruction Manual preview
luna platinum+
Бренд: Baxi Страницы: 156
Truma BG 10 Installation Instructions Manual preview
BG 10
Бренд: Truma Страницы: 44
HTP Elite FT EFT-285 Installation, Start-Up, Maintenance, Parts, Warranty preview
Elite FT EFT-285
Бренд: HTP Страницы: 70
Immergas EOLO Mini S Instruction Booklet preview
EOLO Mini S
Бренд: Immergas Страницы: 27
Immergas EOLO 21 Maior Technical Documentation Manual preview
EOLO 21 Maior
Бренд: Immergas Страницы: 30
Tri-Star TSGCB-18i Installation And Operating Instructions Manual preview
TSGCB-18i
Бренд: Tri-Star Страницы: 19
Bryan Boilers LDTV-10 Specification Sheet preview
LDTV-10
Бренд: Bryan Boilers Страницы: 2
Bryan Boilers CFS-15-20-20D Specification Sheet preview
CFS-15-20-20D
Бренд: Bryan Boilers Страницы: 2
Ideal Boilers excel HE C24 User Manual preview
excel HE C24
Бренд: Ideal Boilers Страницы: 4
Bryant BW4 Installation Instructions Manual preview
BW4
Бренд: Bryant Страницы: 26
Electric Heating Company EHCCOM12KW Installation And Technical Manual preview
EHCCOM12KW
Бренд: Electric Heating Company Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды