HTP MODCON1000 Скачать руководство пользователя | Manualshive

Страница: 67 / 81

background image

67

LP- 428 REV. 9.2.14

Figure 29

PART 13 – MAINTENANCE

In unusually dirty or dusty conditions, care must be taken to keep appliance cabinet door in place at all times. Failure to do so VOIDS
WARRANTY!

Allowing the appliance to operate with a dirty combustion chamber will hurt operation. Failure to clean the heat exchanger as needed by
the installation location could result in appliance failure, property damage, personal injury, or death. Such product failures ARE NOT
covered under warranty.

The appliance requires minimal periodic maintenance under normal conditions. However, in unusually dirty or dusty conditions, periodic
vacuuming of the cover to maintain visibility of the display and indicators is recommended.

A. MAINTENANCE PROCEDURES

Periodic maintenance should be performed once a year by a qualified service technician to assure that all equipment is operating safely
and efficiently. The owner should make necessary arrangements with a qualified heating contractor for periodic maintenance of the
heater. Installer must also inform the owner that the lack of proper care and maintenance of the heater may result in a hazardous
condition.

BEFORE EACH HEATING SEASON a trained and qualified service technician should perform the inspections as per the boiler
inspection and maintenance schedule in the back of this manual. Failure to do so could result in death or serious injury.

«
...
65
66
67
68
69
...
»

Содержание MODCON1000


















































































Отзывы:

Нет отзывов

Похожие инструкции для MODCON1000

Бренд: Varmebaronen Страницы: 16

Бренд: Froling Страницы: 35

Бренд: Ideal Boilers Страницы: 8

Premier E-HR 24

Бренд: Atag Страницы: 32

Бренд: Lochinvar Страницы: 16

Eclipse 216 ESS

Бренд: VOKERA Страницы: 40

Бренд: Biasi Страницы: 84

Бренд: Laars Страницы: 118

Бренд: Garland Страницы: 2

Бренд: REMEHA Страницы: 44

Бренд: Lochinvar Страницы: 12

Greenstar Danesmoor Utility ErP 50/70

Бренд: Worcester Страницы: 16

Бренд: ACV Страницы: 154

Бренд: Zojirushi Страницы: 38

Бренд: CleaverBrooks Страницы: 64

ELTHERM M Series

Бренд: green ecotherm Страницы: 34

Prestige PARKIT101

Бренд: TriangleTube Страницы: 6

Бренд: Glen Dimplex Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды