HTP MODCON1000 Скачать руководство пользователя | Manualshive

Страница: 35 / 81

background image

35

LP- 428 REV. 9.2.14

Figure 16

– Unbalanced Venting

NOTE:

Exhaust vent must always be piped vertically in an unbalanced venting configuration.

Take extra precaution to adequately support the weight of vent pipes terminating through the roof. Failure to properly support roof
terminated vent piping could result in property damage, serious personal injury, or death due to flue gas leakage.

All vent pipes must be glued, properly supporte

d, and the exhaust must be pitched a minimum of ¼” per foot back to the boiler to allow

drainage of condensate. Exhaust connection insertion depth should be a minimum of 2 ½” for 500 models and 3” for 850. When placing
support brackets on vent piping, the

first bracket must be within 1’ of the appliance and the balance at 4’ intervals on the vent pipe.

Boiler venting must be readily accessible for visual inspection for the first three feet from the boiler.

«
...
33
34
35
36
37
...
»

Содержание MODCON1000


















































































Отзывы:

Нет отзывов

Похожие инструкции для MODCON1000

Бренд: Baxi Страницы: 16

Proteus Premix Series

Бренд: E.C.A. Страницы: 42

Бренд: Ariston Страницы: 12

Бренд: Blodgett Страницы: 2

Бренд: Lochinvar Страницы: 16

Бренд: Lochinvar Страницы: 44

Бренд: Lochinvar Страницы: 40

Бренд: Immergas Страницы: 27

Бренд: Immergas Страницы: 30

EVO-COOL CS 1300

Бренд: Viessmann Страницы: 36

Бренд: Viessmann Страницы: 44

Бренд: Aerco Страницы: 206

DEVYL 11 D ie FF

Бренд: sylber Страницы: 92

Netaheat Electronic 10/16

Бренд: Potterton Страницы: 24

Бренд: Glow-worm Страницы: 24

Бренд: Rinnai Страницы: 28

Бренд: Rinnai Страницы: 64

Бренд: Britony Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды