manualshive.com logo in svg

HTP MODCON1000, Установка, Запуск, Обслуживание, Запчасти, Гарантия

HTP MODCON1000 - высококачественный продукт для отопления. Данный газовый котел обеспечивает максимальный комфорт и экономичность. Установка, запуск и обслуживание легко выполняются с помощью бесплатного руководства по эксплуатации, доступного для загрузки на manualshive.com. Гарантия и запчасти также включены.

Поделиться
Скачать
background image

59 

 

 

                                                                                     LP- 428 REV. 9.2.14 

Press the 

▼ key once. 

OUTDOOR       11 

o

F 

FLUE                95 

o

F

 

The current outdoor temperature is displayed on the top line. If there is no outdoor sensor connected to the 
boiler

, this line will display ‘OFF’ in place of the temperature. If the outdoor sensor is shorted, this line will display 

‘ON’ in place of the temperature. The second line displays the current flue temperature of the boiler. 

Press the 

▼ key once.

 

FLAME                  0.0uA 
FAN SPEED   3497 RPM 

This screen displays the boiler flame current on the top line. The second line displays the fan speed in the boiler.

 

Press the 

▼ key once. 

0-10 V                    0.0 V 
BOILER 

The top line displays the voltage on the optional input. This voltage is only relevant if an external 0-10 volt signal 
is being used to control the boiler.

 

Press the 

▼ key once. 

BUS COMM       NO CONN 
 

This display shows the status of the communication bus between multiple boilers. If the boiler is in a single boiler 
configuration, the display will show ‘NO CONN’. If the boiler is used in a multiple coiler configuration, is the 
Master Boiler, and other boilers are connected to the communication bus and powered, this screen will show the 
address of each boiler connected to the bus.

 

Press the 

▼ key once. 

POWER ON           0H 
CH ON                   0H 

The top line of this display indicates the amount of hours the boiler has had power applied to it over its life. The 
second line indicates how many hours the burner has been on for central heat demand over its life.

 

Press the 

▼ key once. 

DHW  ON            

0H 

GOOD  IGNIT 

1X 

The top line of this display indicates the amount of hours the burner has been on for domestic hot water demand 
in the life of the boiler. The second line indicates how many times the burner has successfully ignited in the life 
of the boiler.

 

Press the 

▼ key once. 

SYS  CH  ON           0h 
SYS  DWH  ON        0h 

This screen displays how many hours the boiler has run to meet central heat and DWH demand.

 

Table 18 

– Boiler Control Status Menu Screens 

The following 10 screens display the last ten boiler lockout faults. The faults are displayed from most recent to oldest by pressing the 

▼ 

key. 

SCREEN 

DESCRIPTION 

Press the 

▼ key once. 

FAULT  HISTORY           1 
07/27/2009        Mo  5:19A

 

This screen displays the last lockout fault the boiler controller had. The top line will alternate between the words 
‘FAULT HISTORY’ and the actual fault encountered. The bottom line displays the date and time the fault 
occurred. 

Press the 

▼ key once.

 

FAULT HISTORY           2 
08/28/2009         Fr  5:19A

 

This screen displays the second oldest lockout fault that occurred in the boiler controller. The top line will 
alternate between the words ‘FAULT HISTORY’ and the actual fault encountered. The bottom line will display 
the date and time that the fault occurred.

 

Press the 

▼ key once.

 

FAULT HISTORY           3 
08/28/2009         Fr  5:19A

 

This screen displays the third oldest lockout fault that occurred in the boiler controller. The top line will alternate 
between the words ‘FAULT HISTORY’ and the actual fault encountered if one has occurred. The bottom line 
displays the date and time a fault occurred.

 

Press the 

▼ key once. 

FAULT HISTORY           4 
08/28/2009         Fr  5:19A

 

This screen displays the fourth oldest lockout fault that occurred in the boiler controller. The top line will alternate 
between the words ‘FAULT HISTORY’ and the fault encountered. The bottom line displays the date and time the 
fault occurred.

 

Press the 

▼ key once. 

FAULT HISTORY           5 
08/28/2009         Fr  5:19A

 

This screen displays the fifth oldest lockout fault that occurred in the boiler controller. The top line will alternate 
between the words ‘FAULT HISTORY’ and the fault encountered. The bottom line displays the date and time the 
fault occurred.

 

Press the 

▼ key once. 

FAULT HISTORY           6 
08/28/2009         Fr  5:19A

 

This screen displays the sixth oldest lockout fault that occurred in the boiler controller. The top line will alternate 
between the words ‘FAULT HISTORY’ and the fault encountered. The bottom line displays the date and time the 
fault occurred.

 

Press the 

▼ key once.

 

FAULT HISTORY           7 
08/28/2009         Fr  5:19A 

This screen displays the seventh oldest lockout fault that occurred in the boiler controller. The top line will 
alternate between the words ‘FAULT HISTORY’ and the fault encountered. The bottom line displays the date 
and time the fault occurred.

 

Press the 

▼ key once. 

FAULT HISTORY           8 
08/28/2009         Fr  5:19A 

This screen displays the eighth oldest lockout fault that occurred in the boiler controller. The top line will 
alternat

e between the words ‘FAULT HISTORY’ and the fault encountered. The bottom line displays the date 

and time the fault occurred.

 

Press the 

▼ key once. 

FAULT HISTORY           9 
08/28/2009         Fr  5:19A 

This screen displays the ninth oldest lockout fault that occurred in the boiler controller. The top line will alternate 
between the words ‘FAULT HISTORY’ and the fault encountered. The bottom line displays the date and time the 
fault occurred.

 

Содержание MODCON1000


















































































Отзывы:

Нет отзывов

Похожие инструкции для MODCON1000

IBC VX Series Installation & Operating Manual preview
VX Series
Бренд: IBC Страницы: 111
Navien NCB-190/060H Installation & Operation Manual preview
NCB-190/060H
Бренд: Navien Страницы: 145
Garland 6-40R Service Manual preview
6-40R
Бренд: Garland Страницы: 28
Worcester GR8700iW 30 S LPG User Instructions preview
GR8700iW 30 S LPG
Бренд: Worcester Страницы: 16
Navien NFC-200 Quick Installation Manual preview
NFC-200
Бренд: Navien Страницы: 4
CHAFFOTEAUX PHAROS GREEN User Manual preview
PHAROS GREEN
Бренд: CHAFFOTEAUX Страницы: 16
Navien NFB Series Installation & Operation Manual preview
NFB Series
Бренд: Navien Страницы: 232
Mikrofill Ethos 28 Series Installation And Operating Manual preview
Ethos 28 Series
Бренд: Mikrofill Страницы: 66
Unical NUA Installation And Maintenance Instructions Manual preview
NUA
Бренд: Unical Страницы: 112
Welbilt Cleveland 24CGP10 Operation Installation Maintenance Manual preview
Cleveland 24CGP10
Бренд: Welbilt Страницы: 42
Navien NHB-055H User'S Information Manual preview
NHB-055H
Бренд: Navien Страницы: 29
Kiturami KF-35B User Manual preview
KF-35B
Бренд: Kiturami Страницы: 20
Baxi Potterton Suprima 30 HE User Manual preview
Potterton Suprima 30 HE
Бренд: Baxi Страницы: 8
Baxi Luna Platinum 1.12 Manual preview
Luna Platinum 1.12
Бренд: Baxi Страницы: 37
Baxi Mainfour 24-24F Operating And Installation Instructions preview
Mainfour 24-24F
Бренд: Baxi Страницы: 204
Express AS18 User Instructions preview
AS18
Бренд: Express Страницы: 4
Viessmann C3HA Installation And Service Instructions For Contractors preview
C3HA
Бренд: Viessmann Страницы: 192
Unical ALKON 100 EXT Installation And Servicing Manual preview
ALKON 100 EXT
Бренд: Unical Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды