manualshive.com logo in svg

HTP MODCON1000, Установка, Запуск, Обслуживание, Запчасти, Гарантия

HTP MODCON1000 - высококачественный продукт для отопления. Данный газовый котел обеспечивает максимальный комфорт и экономичность. Установка, запуск и обслуживание легко выполняются с помощью бесплатного руководства по эксплуатации, доступного для загрузки на manualshive.com. Гарантия и запчасти также включены.

Поделиться
Скачать
background image

7 

 

 

                                                                                     LP- 428 REV. 9.2.14 

B. COMBUSTION CHAMBER COIL CLEANING INSTRUCTIONS FOR HEATER ...................................................................... 68

 

BOILER START-UP REPORT ................................................................................................................................................... 76

 

MAINTENANCE REPORT ......................................................................................................................................................... 76

 

MAINTENANCE NOTES .................................................................................................................................................................. 80

 

HTP CUSTOMER INSTALLATION RECORD FORM...................................................................................................................... 81

 

 

PART 1 – GENERAL SAFETY INFORMATION 

A. PRECAUTIONS 

This appliance is for indoor installations only. Clearance to combustible materials: 0” top, bottom, sides and back. Front must have 
room for se

rvice, 24” recommended. (A combustible door or removable panel is acceptable front clearance.) This appliance has been 

approved for closet installation. Do not install this appliance directly on carpeting. This appliance may be installed on combustible 
flooring. For use with Category IV vent systems only. 
 

 

INSTALLER 

– 

Read all instructions in this manual before installing. Perform steps in the order given. 

USER 

– 

This manual is for use only by a qualified heating installer/service technician. Refer to u

ser’s information manual for your 

reference. Have this boiler serviced/inspected by a qualified service technician annually.

 

FAILURE  TO  ADHERE  TO  THE  GUIDELINES  ON  THIS  PAGE  AND  HAVE  THIS  BOILER  SERVICED/INSPECTED  ANNUALLY 
CAN RESULT IN SUBSTANTIAL PROPERTY DAMAGE, SEVERE PERSONAL INJURY, OR DEATH. 

 

 

DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN SUBMERGED IN WATER.

 Immediately call a qualified service technician. 

The appliance MUST BE replaced if it has been submerged. Attempting to operate an appliance that has been submerged could create 
numerous harmful conditions, such as a potential gas leakage causing a fire and/or explosion, or the release of mold, bacteria, or other 
harmful particulates into the air. Operating a previously submerged appliance could result in property damage, severe personal injury, 
or death. 
 

NOTE:

 Appliance damage due to flood or submersion is considered an Act of God, and IS NOT covered under product warranty. 

 

NOTE:

 If the boiler is exposed to the following, do not operate until all corrective steps have been made by a qualified serviceman: 

 

FIRE  

 

DAMAGE  

 

WATER 

Any claims for damage or shortage in shipment must be filed immediately against the transportation company by the consignee. 
 

 

Due to low water content of the boiler, improperly sizing the boiler in regard to heating system load will result in excessive boiler cycling 
and accelerated component failure. HTP 

DOES NOT 

warrant failures caused by improperly sized boiler applications. 

DO NOT

 oversize 

the boiler to the system. Modular boiler installations greatly reduce the likelihood of boiler oversizing

.

 

B. GAS 

Should overheating occur or gas supply fail to shut off, do not turn off or disconnect electrical supply to the circulator. Instead, shut off 
the gas supply at a location external to the appliance. 

C. IMPROPER COMBUSTION 

D. WHEN SERVICING THE BOILER 

 

To avoid electric shock, disconnect electrical supply before performing maintenance. 

 

Do not obstruct the flow of combustion and ventilating air. Adequate air must be provided for safe operation.  Failure to keep the 
exhaust vent and intake pipe clear of ice, snow, or other debris could result in property damage, serious personal injury, or death. 

Содержание MODCON1000


















































































Отзывы:

Нет отзывов

Похожие инструкции для MODCON1000

Riello RTQ 1074 Installation, Operation, Maintenance And System Management Manual preview
RTQ 1074
Бренд: Riello Страницы: 28
Alarko HARMONY - D Installation And Servicing Instructions preview
HARMONY - D
Бренд: Alarko Страницы: 72
Immergas 3.024488 Instruction For Technician And Installer preview
3.024488
Бренд: Immergas Страницы: 44
Ariston GENUS HE 35 Plus Installation And Servicing Instrucnion preview
GENUS HE 35 Plus
Бренд: Ariston Страницы: 68
Immergas 3.015266 Quick Start Manual preview
3.015266
Бренд: Immergas Страницы: 4
Viadrus HERCULES DUO Manual For Operation And Installation preview
HERCULES DUO
Бренд: Viadrus Страницы: 76
Radiant Slim RBA CS 24 E Installation And Maintenance Manual preview
Slim RBA CS 24 E
Бренд: Radiant Страницы: 38
ENERGY KINETICS Resolute Boiler Installation & Service Manual preview
Resolute Boiler
Бренд: ENERGY KINETICS Страницы: 42
Radiant R1K 100 RAIN Installation And Maintenance Manual preview
R1K 100 RAIN
Бренд: Radiant Страницы: 64
Camus Hydronics MFH060 Installation, Operation And Service Manual preview
MFH060
Бренд: Camus Hydronics Страницы: 66
Astra G-100 MES Manual Of Installation And Exploitation preview
G-100 MES
Бренд: Astra Страницы: 19
Nieco 930 GAS Owner'S Manual preview
930 GAS
Бренд: Nieco Страницы: 32
Beretta CIAO GREEN C.S.I. Installer And User Manual preview
CIAO GREEN C.S.I.
Бренд: Beretta Страницы: 50
Beretta EXCLUSIVE GREEN 16 RSI Installation And User Manual preview
EXCLUSIVE GREEN 16 RSI
Бренд: Beretta Страницы: 100
Beretta EXCLUSIVE C Installer And User Manual preview
EXCLUSIVE C
Бренд: Beretta Страницы: 102
Beretta EXCLUSIVE BOILER GREEN 30 B.S.I. Installer And User Manual preview
EXCLUSIVE BOILER GREEN 30 B.S.I.
Бренд: Beretta Страницы: 116
Ferroli ATLAS D ECO 34 COND SI UNIT Instructions For Use, Installation And Maintenance preview
ATLAS D ECO 34 COND SI UNIT
Бренд: Ferroli Страницы: 112
PAW HeatBloC K36 Installation And Operation Instructions Manual preview
HeatBloC K36
Бренд: PAW Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды