background image

Prestige

Display Module  Replacement 

1

WARNING

!

Indicates a potentially hazardous situation which, 
if ignored, can result in serious  injury or substan-
tial property damage.

NOTICE

Indicates special instructions on installation, operation 

or maintenance, which are important to equipment 

but not related to personal injury hazards.

WARNING

!

For your safety, turn off electrical power supply 
at service panel and allow unit to cool before pro-
ceeding to avoid possible electrical shock and 
scald hazard.  Failure to do so can cause severe 
personal injury or death.

WARNING

!

Failure to follow instructions below can result in 
severe personal injury or damage if ignored.

•  Instructions are for a qualified installer/ ser-

vice technician only.

•  Read all instructions before proceeding.
•  Follow instructions in proper order.

Each Kit Includes:

•  Display Module

•  (6) Screws 

Recommended Tools:

•  Flathead Screwdriver

•  Phillips Head Screwdriver 

Kit Part Number

Description

Model

PARKIT101

Display Module Replacement

All Models

2020-20 Prestige Display Module Replacement

Revised 1/22/2020

Summary of Contents for Prestige PARKIT101







Reviews: