HP StorageWorks 2000fc Скачать руководство пользователя страница 299 | Manualshive

Страница: 299 / 330

background image

Appendix E

Event Codes

299

307

Critical

A temperature sensor on a controller
FRU detected an over-temperature
condition that caused the controller to
shut down.

• Check that the storage system’s

fans are running.

• Check that the ambient

temperature is not too warm. The
enclosure operating range is
41

°

F to 104

°

F (5

°

C to 40

°

C).

• Check for any obstructions to the

airflow.

• If none of the above explanations

apply, replace the controller FRU
that reported the error.

308

Informational

The default host port speed has
changed from 4 Gbit/sec to 2 Gbit/sec
because the controller module’s HIM
has a Broadcom PBC.

309

Informational

Normally when the Management
Controller is started, the IP data is
obtained from the SEEPROM where
it is persisted. If the system is unable
to write it to the SEEPROM the last
time it changed, a flag is set in flash
memory. This flag is set during
startup, and if set, this event is logged
and the IP data that is in flash
memory is used. The only time that
this would not be the correct IP data
would be if the controller board was
swapped and then whatever data is on
the board’s flash memory is used.

310

Informational

After a rescan, the controller
completed back-end discovery and
initialization of enclosure data.

313

Critical

An I/O module is down and will not
be automatically restarted. This only
applies when the other SC goes
down.

The SC needs service or
replacement.

TABLE E-1

Event Descriptions and Recommended Actions

(Continued)

Event
Code

Event Type

Description

Recommended Action

«
...
297
298
299
300
301
...
»

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks 2000fc

Flex System EN4132

Бренд: IBM Страницы: 11

Бренд: Magnadyne Страницы: 2

Бренд: Radicom Research Страницы: 9

Бренд: 3idee Страницы: 5

Бренд: 3idee Страницы: 5

Бренд: 3idee Страницы: 7

Nano Bluetooth USB-Adapter

Бренд: Hama Страницы: 26

Бренд: Devolo Страницы: 16

Бренд: National Instruments Страницы: 6

Бренд: DeLOCK Страницы: 4

UltraAV DisplayPort

Бренд: Accell Страницы: 2

Бренд: StarTech.com Страницы: 9

ConnectLine Phone Adapter 2.0

Бренд: oticon Страницы: 26

Бренд: BeachTek Страницы: 2

Бренд: Digitus Страницы: 7

Бренд: Chamberlain Страницы: 1

Бренд: Lenze Страницы: 18

Бренд: Johnson Controls Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды