manualshive.com logo in svg

HP StorageWorks 2000fc, Справочное руководство

Хранилище данных HP StorageWorks 2000fc представляет собой универсальное устройство для хранения информации. Спецификация, руководство пользователя и другие документы доступны для бесплатной загрузки с manualshive.com. Технические характеристики и руководство по эксплуатации помогут максимально эффективно использовать этот продукт.

Поделиться
Скачать
background image

288

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

168

Warning or 
informational

The specified SES alert condition was 
detected in the enclosure indicated.

Most voltage and temperature 
errors and warnings relate to the 
power-and-cooling module. 
See “Power-and-Cooling Module 
Faults and Recommended Actions” 
on page 302.

169

Informational

The specified SES alert condition has 
been cleared in the enclosure 
indicated.

This event is generated when the 
problem that caused event 168 is 
cleared. 

170

Informational

The last rescan indicates that the 
specified enclosure was added to the 
system.

171

Informational

The last rescan indicates that the 
specified enclosure was removed 
from the system.

172

Warning

The specified vdisk has been 
quarantined because not all of its 
drives are available. There are not 
enough drives to be fault tolerant. 
The partial vdisk will be held in 
quarantine until it becomes fault 
tolerant.

• Ensure that all drives are latched 

into their slots and have power.

• During quarantine, the vdisk is 

not visible to the host. If after 
latching drives into their slot and 
powering up the vdisk, the vdisk 
is still quarantined, you can 
manually remove the vdisk from 
quarantine so that the host can 
see the vdisk. The vdisk is still 
critical. 

When the vdisk has been removed 
from quarantine, event 173 is 
logged.

173

Informational

The specified vdisk has been removed 
from quarantine.

174

Informational

A device firmware update has 
completed.

175

Informational

An Ethernet link has changed status 
(up/down).

TABLE E-1 

Event Descriptions and Recommended Actions 

(Continued)

Event 
Code

Event Type

Description

Recommended Action

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks 2000fc

3idee hp-32f Assembly Instructions Manual preview
hp-32f
Бренд: 3idee Страницы: 7
aqprox! appUSB150DAV2 User Manual preview
appUSB150DAV2
Бренд: aqprox! Страницы: 37
Sharkoon Mobile DAC Manual preview
Mobile DAC
Бренд: Sharkoon Страницы: 40
Aiphone RY-IP44 Programming Manual preview
RY-IP44
Бренд: Aiphone Страницы: 15
ZyXEL Communications NWD-210N - V1.0 User Manual preview
NWD-210N - V1.0
Бренд: ZyXEL Communications Страницы: 152
NETGEAR MA 101 Specifications preview
MA 101
Бренд: NETGEAR Страницы: 2
ATI Technologies Component Video Adapter Installation And Setup User'S Manual preview
Component Video Adapter
Бренд: ATI Technologies Страницы: 16
l-com UMC-201 User Manual preview
UMC-201
Бренд: l-com Страницы: 54
Vega VEGACONNECT Operating Instructions Manual preview
VEGACONNECT
Бренд: Vega Страницы: 24
Jabra Link 950 USB-A Quick Start Manual preview
Link 950 USB-A
Бренд: Jabra Страницы: 2
Xylem ebro AL 126 Manual preview
ebro AL 126
Бренд: Xylem Страницы: 16
NETGEAR XET1001 - Powerline Network Adapter Installation Manual preview
XET1001 - Powerline Network Adapter
Бренд: NETGEAR Страницы: 2
Siemens INSYS Pocket ISDN-TA Operating Manual preview
INSYS Pocket ISDN-TA
Бренд: Siemens Страницы: 44
Siemens 8US1240-5MA00 Operating Instructions preview
8US1240-5MA00
Бренд: Siemens Страницы: 4
Siemens 8US1213-4AU01 Operating Instructions preview
8US1213-4AU01
Бренд: Siemens Страницы: 4
Siemens 8US1213-4AP03 Installation Instructions preview
8US1213-4AP03
Бренд: Siemens Страницы: 4
Siemens 8US1213-4AH04 Operating Instructions preview
8US1213-4AH04
Бренд: Siemens Страницы: 4
Siemens 8US1211-4TR00 Operating Instructions preview
8US1211-4TR00
Бренд: Siemens Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды