HP StorageWorks 2000fc Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 330

background image

Chapter 2

Configuring Your System for the First Time

59

The disadvantage of ICPM is that if a controller fails, the other controller cannot fail
over (that is, take over I/O processing for the failed controller). If a controller fails,
the host loses access to the volumes owned by that controller. If a controller
experienced a complete hardware failure, and needed to be replaced, then user data
in its write-back cache is lost.

Data loss does not automatically occur if a controller experiences a software
exception, or if a controller module is removed from the enclosure. However, if a
controller is damaged in a nonrecoverable way then you might lose data in ICPM.

Caution –

Data might be compromised if a RAID controller failure occurs after it

has accepted write data, but before that data has reached the disk drives. Do

not

use

ICPM in an environment that requires fault tolerance.

Note –

Independent cache performance mode disables partner firmware upgrade.

Controllers must be upgraded manually.

To enable or disable Independent Cache Performance Mode:

1. Select Manage > General Config > System Configuration.

2. Click Advanced Options.

3. In the Change Independent Cache Performance Mode panel, select Enabled or

Disabled. The default is Disabled.

4. Click Enable/Disable Independent Cache Performance Mode.

The system automatically restarts both controllers, which takes several minutes to
complete. If ICPM is enabled, this is shown in each page’s System Panel and in the
Status Message panel on the Status Summary page.

«
...
57
58
59
60
61
...
»

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks 2000fc

Бренд: Otto Bock Страницы: 160

Бренд: StarTech.com Страницы: 15

2870W - annexe 1

Бренд: SMC Networks Страницы: 77

Бренд: Airlink101 Страницы: 47

WMCE54AG - Wireless A/G Media Center Extender

Бренд: Linksys Страницы: 2

NOVA Comet Versaturn

Бренд: Teknatool Страницы: 16

Бренд: StarTech.com Страницы: 2

PRESTO GIGABIT SERVER PCIe

Бренд: Sonnet Страницы: 4

Бренд: Westermo Страницы: 28

FCA2214DC PCI-X

Бренд: HP Страницы: 64

Бренд: HP Страницы: 10

Бренд: NETGEAR Страницы: 12

Бренд: Mitel Страницы: 21

Бренд: Mitel Страницы: 30

Instant Wave High Speed

Бренд: NDC Страницы: 39

Бренд: AVANT Страницы: 30

Motion Sensing Post Light Adapter SL-4100

Бренд: Heath Zenith Страницы: 16

Бренд: Plantronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды