manualshive.com logo in svg

HP StorageWorks 2000fc, Справочное руководство

Поделиться
Скачать
HP StorageWorks 2000fc Скачать руководство пользователя страница 175

Chapter 5

Monitoring System Status

175

To view disk drive information and error statistics:

1. Select Monitor > Statistics > Disk Error Stats.

2. Select the disk drive whose error statistics you want to view.

3. Click Show Disk Drive Error Statistics.

To clear the disk drive error data for the selected drive:

●

Click Clear Selected Disk Drive Error Statistics.

To clear the disk drive error data for all drives:

●

Click Clear All Disk Drive Error Statistics.

I/O Timeout Count

The number of times the drive accepted an I/O request 
but did not complete it in the required amount of time. 
Excessive timeouts can indicate potential device failure 
(media retries or soft, recoverable errors)

No Response Count

The number of times the drive failed to respond to an I/O 
request. A high value can indicate that the drive is too 
busy to respond to further requests.

Spin-up Retries

The number of times the drive failed to start on power-up 
or on a software request. Excessive spin-up retries can 
indicate that a drive is close to failing.

Media Errors

The number of times the drive had to retry an I/O 
operation because the media did not successfully 
record/retrieve the data correctly.

Non Media Errors

The number of soft, recoverable errors that are not 
associated with drive media.

Bad Block Reassignments

The number of block reassignments that have taken place 
since the drive was shipped from the vendor. A large 
number of reallocations in a short period of time could 
indicate a serious condition.

Bad Block List Size

The number of blocks that have been deemed defective 
either from the vendor or over time due to reallocation.

Field

Description

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды