HP StorageWorks 2000fc Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 330

HP StorageWorks 2000fc Скачать руководство пользователя страница 56

56

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

3. Select a value for Maximum Events to Display at One Time.

SMU can display a maximum of 100 events at a time; the default is 10.

For example, if 10 events can display at a time and 15 are pending then the pop-up
window shows the first 10 events and clicking the Acknowledge button will show
the remaining events and new events that might have occurred.

If more than 100 are pending, the oldest ones are dropped.

4. Enable or disable visual notification.

The default is Enable.

5. Click Change Visual Alerts Configuration.

Note –

Special events prompt you to take a specific action based on the event. The

prompt is displayed in place of the normal Acknowledge button. For example, when
the “Unwritable cache data exists for virtual disk” event occurs, you are prompted
to either keep or discard the cache data.

Note –

To view events that have been acknowledged or that don't cause

notifications, click

in the System Panel.

Configuring Email Alerts

You can configure the following options for email notification of events:

■

Email addresses to send notification messages to

■

A comment to include in each message

■

The mail server IP address

■

The sender name and domain name

■

Whether email alerts are enabled or disabled

You can also test the email configuration.

To configure and test email notification:

1. Select Manage > Event Notification > Email Configuration.

«
...
54
55
56
57
58
...
»

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды