HP StorageWorks 2000fc Скачать руководство пользователя страница 279 | Manualshive

Страница: 279 / 330

background image

Appendix E

Event Codes

279

45

Informational

A communication failure has
occurred between the controller and
an EMP.

47

Informational

An error detected by the sensors has
been cleared.

48

Informational

The vdisk name has been changed.

49

Informational

A lengthy SCSI maintenance
command has completed.

52

Informational

Vdisk expansion has started.

This operation can take days to
complete.

53

Informational
or warning

This event is logged as informational
when a vdisk expansion has
completed or a RAID morph
operation is canceled by the user.
This event is logged as a warning if
the RAID morph operation fails.

55

Informational

A SMART event occurred on the
specified drive.

Impending drive failure. See “Disk
Drive Errors and Recommended
Actions” on page 300.

56

Informational

The Storage Controller has been
restarted.

58

Warning or
informational

A disk drive or other SCSI device
(such as an EMP) detected an error.
This event is logged as a warning for
serious errors such as parity or drive
hardware failure, and as
informational for other errors.

• For warning events that indicate

a disk drive is bad, replace that
drive module.

• For warning events that indicate

an expansion module is bad,
replace that expansion module.

59

Warning or
informational

The controller detected an error while
communicating with the specified
SCSI device. The error was detected
by the controller, not the disk. This
event is logged as a warning for
parity errors, and as informational for
other errors.

• For warning events that indicate

a disk drive is bad, replace that
drive module.

• For warning events that indicate

an expansion module is bad,
replace that expansion module.

TABLE E-1

Event Descriptions and Recommended Actions

(Continued)

Event
Code

Event Type

Description

Recommended Action

«
...
277
278
279
280
281
...
»

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks 2000fc

Бренд: Ubiquiti Страницы: 24

Бренд: U.S. Converters Страницы: 49

Бренд: Telex Страницы: 6

P-Link 0.3 WiFi Kit

Бренд: Tele System Страницы: 24

Бренд: Cables to Go Страницы: 21

Бренд: QOLSYS Страницы: 2

Бренд: HumminGuru Страницы: 2

Бренд: Lindy Страницы: 2

Бренд: Yealink Страницы: 8

Portico TVA Series

Бренд: Citel Страницы: 109

Бренд: UCONNECT INTERNATIONAL Страницы: 8

Бренд: Abus Страницы: 23

ThinkServer LPe12000

Бренд: Lenovo Страницы: 22

Бренд: Simple Audio Страницы: 16

Бренд: PointMobi Страницы: 9

USB100TX - EtherFast 10/100 USB Network Adapter

Бренд: Linksys Страницы: 2

Бренд: BECKWITH ELECTRIC Страницы: 25

Бренд: TRENDnet Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды