HP StorageWorks 2000fc Скачать руководство пользователя страница 298

Страница: 298 / 330

298

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

298

Warning

The controller’s real-time clock
(RTC) settings might be invalid after
an unexpected power loss.

Check the system date and time. If
either is incorrect, set them to the
correct date and time.

299

Informational

The controller’s real-time clock
(RTC) settings were recovered after
an unexpected power loss.

300

Informational

CPU frequency has been adjusted to
high.

301

Informational

CPU frequency has been adjusted to
low.

302

Informational

DDR memory clock has been
adjusted to high.

303

Informational

DDR memory clock has been
adjusted to low.

304

Informational

The controller has detected I

C errors

that may have been fully recovered.
This event is logged as informational
to note an existence of previous I

errors.

305

Informational

A serial number in Storage Controller
flash memory is invalid. The valid
serial number will be recovered
automatically.

306

Informational

An old serial number in Storage
Controller flash memory has been
updated to a new serial number.

TABLE E-1

Event Descriptions and Recommended Actions

(Continued)

Event
Code

Event Type

Description

Recommended Action

Содержание StorageWorks 2000fc











































































































































































































































































































































Результаты поиска

Содержание StorageWorks 2000fc

Отзывы:

Бренды по названию

Популярные бренды

HP StorageWorks 2000fc, Справочное руководство

Результаты поиска

Содержание StorageWorks 2000fc

Отзывы:

Бренды по названию

Популярные бренды