manualshive.com logo in svg

HP StorageWorks 2000fc, Справочное руководство

Поделиться
Скачать
HP StorageWorks 2000fc Скачать руководство пользователя страница 289

Appendix E

Event Codes

289

176

Informational

The error statistics for the specified 
drive have been reset.

177

Informational

The cache data for a missing volume 
was purged.

178

Informational

A host has been added to the list of 
hosts that can access, or be denied 
access to, a LUN. An Add Host 
command was successful.

179

Informational

A host has been removed from the list 
of hosts that can access or be denied 
access to a LUN. 

180

Informational

Hosts can either access, or be denied 
access to, a LUN. This event 
indicates when a host list type is 
changed from include (to allow 
access) to exclude (to deny access) or 
from exclude to include.

181

Informational

Advanced Network Interface 
Structure was set. The Management 
Controller configuration has been 
changed.

182

Informational

All busses have been paused. I/O will 
not be performed on the drives until 
all busses are unpaused.

183

Informational

All busses have been unpaused, 
meaning that I/O can resume. An 
unpause initiates a rescan.

185

Informational

An EMP write command has 
completed.

186

Informational

Enclosure parameters have been set.

187

Informational

The write-back cache has been 
enabled due to a battery state change. 

188

Informational

Write-back cache has been disabled 
due to a battery state change. 

TABLE E-1 

Event Descriptions and Recommended Actions 

(Continued)

Event 
Code

Event Type

Description

Recommended Action

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды