manualshive.com logo in svg

HP StorageWorks 2000fc, Справочное руководство

Поделиться
Скачать
HP StorageWorks 2000fc Скачать руководство пользователя страница 229

Appendix A

SNMP Configuration

229

FA MIB 2.2 SNMP Behavior

The FA2.2 MIB objects are in compliance with the Fibre Alliance MIB v2.2 
Specification (FA MIB2.2 Spec). For a full description of this MIB, go to:

http://www.fibrealliance.org/fb/mib/mib2_2.htm

FA MIB 2.2 is a subset of FA MIB 4.0, which is included with HP System Insight 
Manager (SIM) and other products. The differences are described in “FA MIB 2.2 
and 4.0 Differences” on page 245.

FA MIB 2.2 was never formally adopted as a standard, but it is widely implemented 
and contains many elements useful for storage products. This MIB generally does 
not reference and integrate with other standard SNMP information; it is 
implemented under the experimental subtree.

Significant status within the device includes such elements as its temperature and 
power sensors, the health of its storage elements such as virtual disks, and the 
failure of any redundant component including an I/O controller.  While sensors can 
be individually queried, for the benefit of network management systems all the 
above elements are combined into an "overall status" sensor.  This is available as 
the unit status (

connUnitStatus

 for the only unit), and a "sensor" in the sensor 

table.

The revisions of the various components within the device can be requested through 
SNMP.

The port section is only relevant to products with Fibre Channel host ports.

The event table allows 400 recently-generated events to be requested.  
Informational, minor, major, or critical event types can be selected; whichever type 
is selected enables the capture of that type and more severe events. This mechanism 
is independent of the assignment of events to be generated into traps.

The traps section is not supported. It has been replaced by an ability to configure 
trap destinations using the CLI or SMU. The statistics section is not implemented.

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды