HP StorageWorks 2000fc Скачать руководство пользователя страница 210

Страница: 210 / 330

210

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

Isolating External Data Path Faults on a SAS
Storage System

To troubleshoot external data path faults, perform the following steps:

1. Select Monitor > Status > Advanced Settings > Host Port Status.

This page provides a graphical representation of controller host port status and port
details.

2. Review the graphical representation of host port status.

■

Green – Host link is healthy

■

Orange – Host link is degraded

■

Red – Host link is down

An indication of link down can be caused by one or more of the following
conditions:

■

A faulty HBA in the host

■

A faulty SAS cable

■

A faulty port in the host interface module

■

A disconnected cable

3. To target the cause of the link failure, view the host port details by clicking on a

port in the graphical view and then reviewing the details listed below it.

The data displayed includes:

■

Topology – Port connection type.

■

Speed – Actual link speed in Gbit per second per PHY lane.

■

Number of Active Lanes - The number of active PHY lanes and the number of
lanes in the port.

■

Port WWN – Port World Wide Name.

■

Health – Port status:

■

Healthy – All PHY lanes are active in the port.

■

Degraded – At least one PHY lane is inactive in the port.

■

SAS Chip Revision – Hardware revision level of the SAS expander processor in
the controller.

■

SAS Libraries Revision – Firmware revision level of the SAS libraries.

Содержание StorageWorks 2000fc











































































































































































































































































































































Результаты поиска

Содержание StorageWorks 2000fc

Отзывы:

Похожие инструкции для StorageWorks 2000fc

Бренды по названию

Популярные бренды

HP StorageWorks 2000fc, Справочное руководство

Результаты поиска

Содержание StorageWorks 2000fc

Отзывы:

Похожие инструкции для StorageWorks 2000fc

Бренды по названию

Популярные бренды