manualshive.com logo in svg

HP StorageWorks 2000fc, Справочное руководство

Поделиться
Скачать
HP StorageWorks 2000fc Скачать руководство пользователя страница 293

Appendix E

Event Codes

293

225

Critical

Background master write copy-on-
write operation has failed. 
There was an internal I/O error. 
Could not complete the write 
operation to the disk.

A probable hardware failure has 
prevented the software from 
operating successfully. Isolate and 
replace and failed hardware 
components. Once the hardware 
issues have been corrected, it might 
be necessary to delete all snapshots 
and restart the controller.

226

Critical

A background master volume 
rollback failed to start due to inability 
to initialize the snap pool. All 
rollback is in a suspended state. 

Make sure the snap pool and the 
vdisk on which this volume exists 
are online. Restart the rollback 
operation.

227

Critical

Failure to execute rollback for a 
particular portion of the master 
volume. 

Restart the rollback operation.

228

Critical

Background rollback for a master 
volume failed to end due to inability 
to initialize the snap pool. All 
rollback is in a suspended state.

Make sure the snap pool and the 
vdisk on which this volume exists 
are online. Restart the rollback 
operation.

229

Warning

The snap pool has reached the snap 
pool warning threshold.

The user can set up the policy for 
the snap pool.

230

Warning

The snap pool has reached the snap 
pool error threshold.
The system will take the action set up 
in the policy. Default is to delete the 
oldest snapshot. 

You can expand the snap pool or 
delete snapshots. 

231

Critical

The snap pool has reached the snap 
pool critical threshold. 
The system will take the action set up 
in the policy. Default is to delete all 
snapshots on the snap pool. 

If the policy is to halt writes, then 
you must free up space on the snap 
pool master, or convert the master 
volume to a standard volume in 
order to resume operations.

232

Warning

The maximum number of enclosures 
allowed for the current configuration 
has been exceeded.

The platform does not support the 
number of enclosures that are 
configured. The firmware has 
removed the enclosure indicated by 
this event from its configuration.

TABLE E-1 

Event Descriptions and Recommended Actions 

(Continued)

Event 
Code

Event Type

Description

Recommended Action

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды