manualshive.com logo in svg

HP StorageWorks 2000fc, Справочное руководство

Поделиться
Скачать
HP StorageWorks 2000fc Скачать руководство пользователя страница 295

Appendix E

Event Codes

295

241–242

Informational

Compact flash status events generated 
by the auto-write-through feature 
whenever an environmental change 
occurs. If an auto-write-through-
trigger condition has been met, write-
back cache is disabled.

243

Informational

A new RAID enclosure has been 
detected. This happens when a 
controller FRU is moved from one 
enclosure to another and the 
enclosure detects that the midplane 
WWN is different from the WWN it 
has in its local flash.

244

Warning

There is not enough space to expand 
the specified snap pool.

Add more storage and retry the 
operation.

245

Informational

An existing disk channel target device 
is not responding to SCSI discovery 
commands. 

Check the indicated target device 
for bad hardware or bad cable, then 
initiate a rescan.

246

Warning

The coin battery is either not present, 
or it is not properly seated, or it has 
reached end of life. (The battery is a 
battery backup for the real-time 
(date/time) clock. In the event of a 
power failure, the date and time will 
revert to 1970 Jan 1 00:00:00.

The coin battery is on the controller 
module. A service technician must 
replace or reseat the battery.

247

Warning

The FRU-ID SEEPROM for the 
specified field replaceable unit (FRU) 
cannot be read; FRU-ID data might 
not be programmed. FRU-ID data 
includes the worldwide name, SCSI 
ID, and branding information.

A service technician can reprogram 
FRU-ID data.

248

Informational

A valid feature license was 
successfully installed. See event 249 
for details about each licensed 
feature.

TABLE E-1 

Event Descriptions and Recommended Actions 

(Continued)

Event 
Code

Event Type

Description

Recommended Action

Содержание StorageWorks 2000fc











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды