HP A7533A - Brocade 4Gb SAN Switch Base, Руководство администратора

Страница: 479 / 576

Fabric OS 6.2 administrator guide 475
11. If you are implementing FICON emulation, configure FICON emulation using the
portCfg ficon
command. See Chapter 23, ” Configuring and monitoring FICON Extension Services ” on page 513 for
specific instructions.
12. If you are implementing FTRACE, configure FTRACE using the
portCfg ftrace
command. See the
Fabric OS Troubleshooting and Diagnostics Guide . for specific instructions.
13. Check the configuration to ensure that the parameters are correct using the
portShow fciptunnel
command.
14. Persistently enable the ports using the
portCfgPersistentEnable
command.
15. Create the same configuration on the HP StorageWorks 400 Multi-Protocol Router or FC4-18i blade at
the other end of the tunnel.
Setting persistently disabled ports
Ports used on an FCIP tunnel must be persistently disabled before you can configure FCIP tunnels. You must
change their state from persistently enabled to persistently disabled. Once the FCIP tunnels have been fully
configured on both ends of the tunnel, you can persistently enable the ports.
1. Enter the
portCfgShow
command to view ports that are persistently disabled.
2. Enter the
portCfgPersistentDisable
command to disable any ports that you will use in the FCIP
tunnel configuration.
Configuring VEX_Ports
If you are going to use a VEX_Port in your tunnel configuration, use the
portCfgVEXPort
command to
configure the port as a VEX_Port. Remember that a VEX_Port must be paired with a VE_Port. VEX_Ports
cannot communicate with other VEX_Ports.
1. Connect to the switch and log in using an account assigned to the admin role.
2. Enter the
portCfgVEXPort
command to configure a port to a VEX_Port. The command syntax is as
follows.
portCfgVEXPort [slot/]portnumber [ge0|ge1] [-a 1|2] [-f fabricid] [-r ratov] [-e
edtov] [-d domainid] [-p 0|1|2] [-t 1|2]
where:
slot The number of the slot in an HP StorageWorks 4/256 SAN Director or HP StorageWorks DC
SAN Backbone Director or HP StorageWorks DC04 SAN Director Switch enterprise-class
platform that contains an FR4-18i blade. This parameter does not apply to the stand-alone HP
StorageWorks 400 Multi-Protocol Router.
ge0|ge1
The Ethernet port used by the tunnel (ge0 or ge1).
-a 1|2
Enables or disables admin (1 to enable or 2 to disable).
-f fabricid
The fabric ID (a number from 1 to 128).
-r ratov
The R_A_TOV used for port negotiation. Valid values are 2000 - 120000. This operand is
applicable only if the "Fabric Parameter" attribute value is not "Auto Negotiate".
-e edtov
The E_D_TOV used for port negotiation. Valid values are 1000 - 60000. This operand is
applicable only if the "Fabric Parameter" attribute value is not "Auto Negotiate".
-d domainid
The preferred domain ID (a number from 1 to 239).
-p 1|2|3
The port ID format (1 for core, 2 for extended edge, and 3 for native).
-t 1|2
Specify 1 to enable or 2 to disable negotiate fabric parameters.
The following example configures a port as a VEX_Port for slot number 8 in port number 18, enables
admin, and specifies fabric ID 2 and preferred domain ID 220:
switch:admin> portcfgvexport 8/18 -a 1 -f 2 -d 220