Honeywell S7999D SOLA Скачать руководство пользователя страница 40

Страница: 40 / 52

65-0315—02

Fig. 92. Vessel analysis page.

Data included in the vessel analysis graph are:

• Outlet temperature

• Inlet temperature

• Heat exchange (outlet – inlet)

• Burner firing rate

Automatic sampling of trend data takes place when the trend

analysis report is displayed. No user intervention is necessary

to invoke sampling.

NOTE: Sample data is collected and stored in the

S7999D. The R7910 or R7911 don’t collect any

historical data for trending purposes. For this

reason any S7999D reset causes all R7910 or

R7911 sampling to start over with no data.

Trend analysis of the following data from each R7910/R7911

is possible:

Trend Analysis Snapshot

The trend analysis snapshot file is stored in Comma

Separated Value (CSV) format in the S7999D so it can be

imported into a spreadsheet program such as Microsoft Excel.

The trend analysis snapshot file can be viewed in graph form

on the S7999D. It can also be copied to a USB device. At any

time, pressing the "camera" button on the top left corner in the

menu bar will capture a screenshot, which can be transferred

to a USB memory stick. Go to Home page--> Setup--> Display

Diagnostics--> Screenshot--> press the snapshot file on the

list --> Copy to USB.

Diagnostics

Pressing the Diagnostics button permits some display

hardware diagnostics (see Fig. 93).

Normally, these

diagnostics are applicable only for factory testing

purposes, but conditions may arise that warrant this

testing.

Table 58. R7910/R7911 Trend Analysis Data.

Data

Comment

Demand source

CH, DHW, LL (Lead Lag), or

FP (Frost Protection) Steam

Sensor

Outlet temperature (R7910

only)
Firing rate

% or RPM

Fan speed

PWM feedback

Flame signal strength

Inlet temperature (R7910

only)

If enabled

DHW temperature (R7910

only)

If enabled

Outdoor temperature

If enabled

Stack temperature

If enabled

Header temperature (R7910

only)

If enabled

CH setpoint

Actual CH setpoint based on

time of day (TOD).

DHW setpoint (R7910 only)

Actual DHW setpoint based

on TOD.

Central Heat Operation

Analysis
Domestic Hot Water

Operation Analysis (R7910

only)
Vessel Analysis

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды