Honeywell S7999D SOLA Скачать руководство пользователя страница 30

Страница: 30 / 52

65-0315—02

DETAILS

Details of the hydronic or steam system is accomplished

through the detail status pages. The detail status page is

shown below.

Screens will appear only if they are configured for your

system.

Information shown is current status. For example: firing rate is

the current fan speed or motor position; timing shown is

current time Sola is at.

Fig. 61. Hydronic CH detail status page.

Status information on the detail status page is organized into

groups and displayed on the page one group at a time. The

user moves from one group to another using the left and right

arrow buttons.

Status data on the detail status page is displayed in a menu

for the group that is currently displayed. If more status items

exist in the group than will fit on the screen, a vertical scroll

bar allows the user to see all status data. If the user selects a

line of status data in the menu, it will expand in bigger, more

easily readable text, as show in Fig. 62. Additional information

about Status data and groups that are displayed are provided

in the R7910 or R7911 Status section of this document.

Fig. 62. Hydronic “expanded” detail status.

R7910 or R7911 Status

Data in Tables 44–Table 55 are displayed on the R7910

Hydronic or R7911 Steam status pages. A complete list of

Status tables can be found in Table 59 on page 42.

The CH status data shown in Table 44 displays first when the

CH Hydronic heating loop is selected on the Home page.

Fig. 63. CH Hydronic Status menu (top).

Table 44. CH Hydronic Status.

Data Comment

CH enable

Enabled, Disabled

CH burner demand

On or Off

CH pump

On or Off

CH pump demand

On or Off

CH pump overrun

time

Running overtime for CH pump

(seconds)

CH requested rate

RPM or %

CH OFF setpoint

Setpoint plus hysteresis

CH setpoint

Temp setting between -40 °F to 266 °F

(-40 °C to 130 °C)

CH ON setpoint

Setpoint minus hysteresis

CH setpoint source

Normal, TOD, Outdoor reset, Remote

control

CH status

Disabled, Normal, Suspended

Demand source

Sensor only, Sensor and Stat terminal,

Sensor and Remote Stat, LCI and

sensor

Outlet high limit

Yes or No

Outlet high limit

setpoint

Temp setting between -40 °F to 266 °F

(-40 °C to 130 °C)

Outlet sensor state

None, Normal, Open, Shorted,

Outside high range, Outside low

range, Not reliable (None = no outlet

sensor)

Outlet temperature

Outlet temperature (same as bar

graph)

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды