Honeywell S7999D SOLA Скачать руководство пользователя страница 23

Страница: 23 / 52

65-0315—02

Annunciation Configuration

Parameters

Table 25 displays annunciation configuration parameters.

Fig. 43. Annunciation configuration example.

Safety Configuration Parameters

Table 26 through 29 display safety parameters.

NOTE: Login is required to change Safety Parameters

and the SOLA Control will go to a Lockout 2

“waiting for safety data verification” when a

change is made.

Fig. 44. Burner Control Interlocks control.

Table 25. Annunciation Configuration Parameters.

Parameter Comment

Annunciation enable Enabled

Disabled

Annunciator (1–8)

location

01 - Annunciator 1

02 - Annunciator 2

03 - Annunciator 3

04 - Annunciator 4

05 - Annunciator 5

06 - Annunciator 6

07 - Annunciator 7

08 - Annunciator 8

PII - Pre-Ignition ILK

LCI - Load Control Input

ILK - Interlock

Annunciator (1–8)

short name

Up to 3 characters

Annunciator (1–8)

name

Up to 20 characters

Table 26. Burner Control

Interlocks Configuration.

Parameter Comment

PII enable

Enabled

Disabled

LCI enable

Enabled

Disabled

Interrupted air switch

(IAS) enable

Enable during purge and ignition

Disabled

Enable during purge

Interlock (ILK) start

check enable

No ILK check

ILK check

ILK/IAS open

response

Recycle

Lockout

ILK bounce detection

enable

Enabled

Disabled

Purge rate proving

Fan Speed

High Fire Switch

None

Lightoff rate proving

Fan Speed

Low Fire Switch

None

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды