Honeywell S7999D SOLA Скачать руководство пользователя страница 31

Страница: 31 / 52

65-0315—02

Fig. 64. CH Hydronic Status menu (middle).

Fig. 65. CH Hydronic Status menu (bottom).

The status data in Table 45 displays first when the DHW

Hydronic heating loop is selected on the Home page. Scrolling

through the status groups eventually shows both.

The bar graph displayed for the CH control loop (hydronic) is

the outlet sensor temperature; for the DHW control loop it is

the DHW sensor temperature. When no analog DHW sensor

is installed (digital switch instead), the inlet sensor

temperature is displayed.

Fig. 66. DHW Hydronic Status menu (top).

Fig. 67. DHW Hydronic Status menu (middle).

Table 45. DHW Hydronic Status.

Data Comment

DHW enable

Enabled, Disabled

Demand source

Unknown, No source demand, CH,

DHW, Lead Lag, CH frost protection,

DHW frost protection, No demand due

to burner switch

DHW burner demand On or Off
DHW high limit

Temp setting between -40 °F to 266 °F

(-40 °C to 130 °C)

DHW high limit

setpoint

Temp setting between -40 °F to 266 °F

(-40 °C to 130 °C)

DHW priority override

time

0-600 seconds

DHW pump

On or Off

DHW pump demand On or Off
DHW pump overrun

time

Running overrun time for DHW pump

(seconds)

DHW requested rate RPM or %
DHW sensor state

None, Normal, Open, Shorted,

Outside high range, Outside low

range, Not reliable (None = no outlet

sensor)

DHW OFF setpoint

Setpoint plus hysteresis

DHW setpoint

Temp setting between -40 °F to 266 °F

(-40 °C to 130 °C)

DHW ON setpoint

Setpoint minus hysteresis

DHW setpoint source Normal, TOD, Outdoor reset
DHW status

Disabled, Normal, Suspended

DHW temperature

DHW temperature (same as bar

graph)

Table 45. DHW Hydronic Status. (Continued)

Data Comment

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды