Honeywell S7999D SOLA Скачать руководство пользователя страница 33

Страница: 33 / 52

65-0315—02

Hydronic Demand and Modulation

Status

Table 47 displays the status page data for R7910.

The bar graph displayed for this status is the outlet sensor

temperature.

Fig. 71. Demand and Modulation Status menu (top).

Fig. 72. Demand and Modulation Status menu (bottom).

Inlet Temperature Status

Table 48 displays the status page data for R7910 inlet

temperature.

The bar graph displayed for this status is the inlet sensor

temperature.

Fan Status

Table 49 displays the status page data for the fan in the

control.

The bar graph displayed for this status is the fan speed.

Fig. 73. Control Fan Status menu.

Table 47. Hydronic Demand and Modulation Status.

Data Comment

Demand source

CH, DHW, Lead Lag, or Frost

Protection (parameter that has current

priority)

Firing rate

% or RPM. Adjustable when firing rate

control set to Manual.

Demand rate

% or RPM.

Rate limiter

None, Outlet high limit, Delta T limit,

Stack limit, Slow start limit, Anti-

condensation, Minimum modulation,

Forced rate

Limited rate

% or RPM

Rate override

Burner control default, Burner control,

manual firing rate off, None

Override rate

% or RPM

Table 48. Inlet High Limit Status.

Data Comment

Inlet sensor state

None, Normal, Open, Shorted,

Outside high range, Outside low

range, Not reliable (None=no outlet

sensor)

Inlet temperature

Inlet sensor temperature (same as bar

graph)

Table 49. Control Fan Status.

Data Comment

Fan speed

% or RPM (current fan speed)

Maximum fan speed Setpoint of maximum fan speed (% or

RPM)

Minimum fan speed

Setpoint of minimum fan speed (% or

RPM)

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды