Honeywell S7999D SOLA Скачать руководство пользователя страница 2

Страница: 2 / 52

65-0315—02

Replacement Parts

50063482-001

Bag assembly includes:

• 8-pin connector

• CR2032 coin battery

• Mounting hardware

• 3 clamp filters (1 for 24V power and 1 for each Modbus)

Fig. 1. S7999D OI Display dimensions in inches (mm).

NOTE: This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial environ-

ment. This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instruction manual, may cause harmful interfer-

ence to radio communications. Operation of this

equipment in a residential area is likely to cause

harmful interference in which case the user will

be required to correct the interference at his own

expense.

The Class A digital apparatus complies with

Canadian ICES-003

SAFETY FEATURES

The OI Display contains software that incorporates many

features that are designed to guide you safely through the

commissioning process. Safety, however, is your

responsibility.

Read all documentation carefully and respond appropriately to

all error messages

WARNING

Explosion Hazard.

Improper configuration can cause fuel buildup and

explosion.

Improper user operation may result in PROPERTY

LOSS, PHYSICAL INJURY or DEATH.

Using the OI Displays to change parameters, must be

attempted by

only experienced and/or licensed

burner/boiler operators and mechanics

INSTALLATION INSTRUCTIONS

The OI Display can be mounted on the door panel of an

electrical enclosure.

Select the location on the door panel to mount the dis-

play; note that the device will extend into the enclosure

at least one inch past the mounting surface.

Provide an opening in the panel door 8" wide X 5 1/2"

high (for front panel mount) or 7 1/8" wide X 4 11/16"

high (for rear panel mount). See Fig. 1 or use cutout

templates provided in Fig. 98 and Fig. 99.

Place the OI Display in the opening and use it as a tem-

plate to mark the location of the four mounting screw

holes. Remove the device.

6-21/32

(169)

9-7/16 (240)

1-27/32

(47)

M32735

PANEL HOLE CUTOUT SIZE FOR FRONT PANEL MOUNT: 8 (203) WIDE X 5-1/2 (140) HIGH.

PANEL HOLE CUTOUT SIZE FOR REAR PANEL MOUNT: 7-1/8 (181) WIDE X 4-11/16 (119) HIGH.

8-15/16 (227)

3-1/2

(89)

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды