Honeywell S7999D SOLA Скачать руководство пользователя страница 22

Страница: 22 / 52

65-0315—02

Anti-Condensation Configuration

Parameters (R7910 Hydronic Control

Only)

Table 23 displays anti-condensation parameters. Use the left

and right arrows to switch between Central Heat, Domestic

Hot Water, Frost Protection, and Priority parameters.

Fig. 41. Anti-condensation configuration.

Frost Protection Parameters

(R7910 Hydronic Control Only)

Table 24 displays frost protection parameters.

Fig. 42. Frost Protection configuration.

Table 23. Anti-Condensation Configuration Parameters.

Parameter

Comment

CH Enable

Enabled

Disabled

CH Setpoint

32 °F to 250 °F (0 °C to 121 °C)

DHW Enable

Enabled

Disabled

DHW Setpoint

32 °F to 250 °F (0 °C to 121 °C)

Frost Protection

Enable

Enabled

Disabled

Anticondensation

Priority

Anticondensation is more important

than (check those that apply):

Stack limit

Delta T limit

Slow start

Forced rate

Outlet high limit

Table 24. Frost Protection Configuration Parameters.

Parameter Comment

CH frost protection

enable

Enabled

Disabled

DHW frost protection

enable

Enabled

Disabled

Lead Lag frost

protection enable

Enabled

Disabled

Outdoor frost

protection setpoint

-40 °F to 266 °F (-40 °C to 130 °C)

(applicable for CH only)

Lead Lag frost

protection rate

___%

CH pump frost

overrun time

___hour ___min ___sec

DHW pump frost

overrun time

___hour ___min ___sec

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды