Honeywell S7999D SOLA Скачать руководство пользователя страница 36

Страница: 36 / 52

65-0315—02

“On” status is indicated by a green LED and “Off” status is

indicated by a gray LED.

Analog I/O data is displayed as bar charts depicting the I/O

level (see Fig. 78). Analog I/O that is not enabled for the

installation displays a blank I/O level. To see all analog I/O,

use the horizontal scroll bar to move the view left and right.

Fig. 78. Diagnostics analog I/O page.

INSTALLER CHECKOUT

Diagnostics Tests

Pressing the Diagnostics Test button launches the diagnostic

tests. The first test displayed on the right side of the screen is

the last selected test shown, as seen in Fig. 79.

This screen enables the user to perform the following tests:

Modulation Test:

enables the user to verify that the burner is

firing at the correct rate. (See Fig. 79.)

Pilot Test:

enables the user to verify that the pilot valve is

functioning properly. The user can also perform burner

adjustments for the pilot flame. (See Fig. 80.)

Pump Test:

enables the user to verify that the correct pump is

on or off. The Start Test button will test all pumps; pressing an

individual pump tests that pump only. (See Fig. 81.)

Burner Switch:

this button turns the burner on or off.

Start Test:

runs the test for 5 minutes.

Fig. 79. Modulation test.

Table 56. Control Digital I/O Data.

Data

Comment

Pump A

On/Off

Pump B

On/Off

Pump C

On/Off

Blower/HSI

On/Off

Pilot valve

On/Off

Main valve

On/Off

Load Control Input

On/Off

STAT

On/Off

Pre-ignition interlock

On/Off

Interlock

On/Off

External ignition

On/Off

Alarm

On/Off

Pilot test hold

On/Off

Time Of Day

On/Off

Safety relay

On/Off

Low Gas

On/Off

High Gas

On/Off

Annunciator 3

On/Off

Annunciator 4

On/Off

Annunciator 5

On/Off

Annunciator 6

On/Off

Annunciator 7

On/Off

Annunciator 8

On/Off

PM Lead/Lag

On/Off

Table 57. Control Analog I/O Data.

Data

Comment

Outlet
Inlet

If enabled

Firing rate

% or RPM

Flame signal

Fan speed

RPM (if applicable). Should

match with firing rate.

Domestic Hot Water

If enabled

Stack

If enabled

Outdoor

If enabled

Header

If enabled

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды