Honeywell S7999D SOLA Скачать руководство пользователя страница 21

Страница: 21 / 52

65-0315—02

Delta T Limit Configuration

Parameters

(R7910 Hydronic Control Only)

Table 20 displays other limit parameters. Use the left and right

arrows to switch between Inlet to Outlet Flow and Exchanger

to Outlet Flow. The parameters are the same for all pumps.

Fig. 40. Delta T Limit configuration.

T-Rise Limit Configuration

Parameters

Table 21 displays T-Rise limit parameters.

Heat Exchanger High Limit

Configuration Parameters

Table 22 displays T-Rise limit parameters.

Table 20. Delta T Limit

Configuration Parameters.

Parameter Comment

Delta T enable

Enabled

Disabled

Delta T degrees

0 °F to 234 °F (-17 °C to 112 °C)

Delta T delay

___hour ___min ___sec

Delta T response

Recycle & delay

Recycle & Delay with retry limit

Lockout

Delta T retry limit

0–100

Delta T rate limit

enable

Enabled

Disabled

Delta T inverse limit

time

___hour ___min ___sec

Delta T inverse limit

response

Recycle & delay

Recycle & delay with retry limit

Lockout

Table 21. T-Rise Limit Configuration Parameters.

Parameter Comment

Outlet T-rise enable

Enabled

Disabled

Heat exchanger T-

rise enable

Enabled

Disabled

T-rise degrees

0 °F to 234 °F (-17 °C to 112 °C)/sec

T-rise response

Recycle & delay

Recycle & delay with retry limit

Lockout

T-rise retry limit

0 to 100

T-rise delay

___hour ___min ___sec

Table 22. Heat Exchanger High Limit

Configuration Parameters.

Parameter Comment

Heat exchanger high

limit enable

Enabled

Disabled

Heat exchanger high

limit setpoint

32 °F to 250 °F (0 °C to 121 °C)

Table 20. Delta T Limit

Configuration Parameters. (Continued)

Содержание S7999D SOLA





















































Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды

Honeywell S7999D SOLA, Руководство пользователя

Результаты поиска

Содержание S7999D SOLA

Отзывы:

Похожие инструкции для S7999D SOLA

Бренды по названию

Популярные бренды