manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 4 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 4

Fire Alarm Control Panel IQ8Control C / M 

 

4

  

FB 798951.10.GB0 / 04.15

 

 

13

 

System overview .................................................................................................................................................... 124

 

14

 

Function for fire alarm control panels ................................................................................................................... 125

 

14.1

 

Use of the loop module in door control systems ........................................................................................... 125

 

15

 

IQ8Wireless ............................................................................................................................................................ 126

 

16

 

Important battery information ................................................................................................................................ 127

 

17

 

Top hat rail mounting kit (Part No. 788652) ......................................................................................................... 128

 

18

 

esserbus

®

 transponder .......................................................................................................................................... 129

 

19

 

Extension housing .................................................................................................................................................. 130

 

19.1

 

Extension housing for two batteries (Part No. 789300 / -01) ........................................................................ 131

 

20

 

Power supply for the built-in printer ...................................................................................................................... 132

 

21

 

Mounting / Replacing of the Panel front + Printer ................................................................................................ 133

 

21.1

 

Heat transfer Printer without paper take-up unit (Part No. 7868xx) ............................................................. 133

 

21.2

 

Printer with paper take-up reel (Part No. 7863xx) ......................................................................................... 135

 

22

 

Fire protection housing F30 .................................................................................................................................. 137

 

 
 
 
 
 
 

 

Additional and updated Informations 

The described features, specifications and product related informations in this manual correspond to 
the date of issue (refer to date on the front page) and may differ due to modifications and/or amended 
Standards and Regulations of the System design, Installation and Commissioning. 

Updated informations and declaration of conformity are available for comparison on the  
www.esser-systems.com homepage.  

esserbus

®

 and essernet

®

 are registered trademarks in Germany. 

 

 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов