Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 129

Страница: 129 / 138

Fire Alarm Control Panel IQ8Control C / M

FB 798951.10.GB0 / 04.15

129

18 esserbus

transponder

esserbus

transponders are input/output modules for extending the control panel inputs/outputs. It is possible to

install up to 32 esserbus

transponders in separate detector zones (separated by zone isolators). Mixing the

operation of fire detectors and esserbus

transponders is not permissible within one detector zone.

The esserbus

transponders is installed either at special fitting locations or with the top hat rail mounting kit

(Part No. 788652) in the Fire Alarm Control Panel, or at decentralised level at any location in a special plastic
housing (e.g. Part No. 788600).

For additional information refer to the Product catalogue fire and documentation of the esserbus

transponder.

For esserbus

PLus loops with a loop voltage of 42 V it is required to connect the appropriate

transponders or devices with the Part No. 80xxxx (see Chapter 5.1.2).

Содержание ESSER IQ8Control M











































































































































Результаты поиска

Содержание ESSER IQ8Control M

Отзывы:

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 129 / 138

Результаты поиска

Содержание ESSER IQ8Control M

Отзывы: