manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 52 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 52

Fire Alarm Control Panel IQ8Control C / M 

 

52

  

FB 798951.10.GB0 / 04.15

 

6.4  Field device module 

The Field device module required in order to configure a stand-alone FACP in accordance to the appropriate 
standards and guidelines. The Field device module integrates all of the input and output modules that are 
necessary in addition to the modules on the Basic module to operate as a Fire Alarm Control Panel to DIN VDE 
0833. This are e.g. terminals to connect a Fire department notifying system, a master box and programmable 
relays.  

 

There are two different kinds of Field device module available for the FACP IQ8Control: 
 

1)  Part No.772477 - Field device module with one micro module slot  

 

2)  Part No.772479 - Field device module without micro module slot 
 
 

 

The FACP must not be operated with series 01 Field device modules.

 

 
 
 

Features 

 

 

Terminals for a Fire Department Notifying System (8 Inputs / 8 Outputs) 

 

Terminals for a Master box (manned centre link) incl. relay to switch the required power supply and monitored 
input to indicate the triggered master box. 

 

Three freely programmable relays – alternatively 
- monitored und positive switching,  
- positive switching  
- or dry change-over contact 

 

Emergency operation for all four relays available 

 
 
 

 

Do not use the relays for the monitored activation of alarm devices. 
Monitoring of the relays is only used to detect interruptions and short circuits. 
 
If a control panel is required to function in accordance with DIN 0833, you should program the relays 
with the >common fire< (K2), >common alarm< (K3) and >common disconnection< (K4) in the 
customer data of the control panel. In the emergency mode the relays will be triggered with the 
assigned function. 
 
If several Fire Alarm Control Panels are connected together in the essernet

®

, the master box can 

be connected to one of the other FACPs. 

 
 

 

Do not connect relays (AE) of the FACP IQ8Control with alternating voltage. Even in the case of a 
>potential free relay< mode it is not possible to switch an external AC-voltage. 

 
 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов