manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 65 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 65

Fire Alarm Control Panel IQ8Control C / M 

 

FB 798951.10.GB0 / 04.15

 

65

 

IQ8Control C 

The Field device module with a single micro module slot (Part No. 772478) must be placed on the >System 
connector 1< of the Basic module. This connector is normally used by the Field device module. Without the field 
device module a system configuration in accordance to the standards is not possible (refer to Chapter 4). 

IQ8Control M 

Up to two connectors are available for Extension modules (Field device and or Extension module). Normally the 
lower >connector 2< is used to connect an Extension module. If required the upper >connector 1< may be used 
too for an Extension module. In this case the integration of an Field device module is impossible. In this case 
mounting of the field device is not possible anymore (see Chapter 4). 

Extension module with a single micro module slot (Part No. 772478) 

This Extension module must be configured in the panels data programming as a Field device module. 

X 1a/2b/3c 

connector 
>System connector 1 or 2< of the Basic modules  

Refer to note! 

X11a/12b 

Connector for a micro module 
(Do not connect an essernet

®

 micro module) Refer to note! 

Refer to note! 

X 10 

Terminals for the micro module wiring.  

Extension module with three micro module slots (Part No.772476) 

Only FACP IQ8Control M configurable. 

LED V1  

ON – Common fire alarm 

LED V2 

ON – CPU failure 

place 1 

Micro module slot only for micro module  

Do not connect an 
essernet

®

 micro module. 

Refer to note! 

place 2 

Micro module slot only for micro module 

place 3 

Micro module slot only for micro module 

X22 

terminal for micro module slot 1 

X23 

terminal for micro module slot 2 

X24 

terminal for micro module slot 3 

X 4/5/6 

Plug contact of 
>System connector 1 or 2< of the Basic module  

Refer to note! 

 

 

If an essernet

® 

micro module is installed, this module can only be operated on the micro module 

slot of the Basic module.  

 
 

6.5.1  Technical Data Extension module 

Operating voltage 

:  Internal via the power supply module, +5 V DC 

Quiescent current  

:  approx. 10 mA  

 

Compatibility : 

Part 

No.772478 

 Extension module with one micro module slot  

Part No.772476 

 Extension module with three micro module slots 

 

 

 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов