manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 137 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 137

Fire Alarm Control Panel IQ8Control C / M 

 

FB 798951.10.GB0 / 04.15

 

137

 

22  Fire protection housing F30 

The fire protection housing provides the installation of Fire Alarm Control Panels IQ8Control in accordance to the 
German MLAR and LAR requirements within corresponding ambient conditions. 
 
Cabling of fire protection equipment must remain in operation at least for 30 minutes to meet the Fire resistance 
rating standard F30 for: 
 

 

Fire Alarm Control Panels incl. alarm transmission devices 

 

Systems for alert and notification of Visitors and Employees, if this function is required for alarm conditions 

 
Fire alarm systems stipulated by constructional law with esserbus

®

 PLus alarm devices, may be operated with 

DiBt approved fire protection housings in accordance to DIN 4102-2. This housing is a part of the systems VDS-
approval and ensures the operation of connected alarm devices above the required 30 minutes. 
 
Furthermore the fire protection housing complies to the German fire load guideline §40 paragraph 2 of the MBO, 
whereby a FACP IQ8Control may be operated in escape routes. Other housings and cases do not meet the 
approval and must not be used for this application. 
 
 
 

 

 

At least a single FACP incl. alarm transmission device must be installed in a fire protection 
housing. 

 

The front door of the housing is closed in normal operation mode. Due to this the user 
operation level 1 (in acc. to EN 54-2) is not accessible. Possibly a Fire department operation 
panel is required by the local authorities. 

 

The housing fan provides a continuous air exchange and causes an ambient noise of min.  
51 dB. Therefore it is recommended not to mount this housings nearby workplaces.  

 

Consider manufactures installation manuals of the housing to mount the FACP! 

 

Warranty is detailed in manufacturers information, company Priorit AG. 

 
 

Housing type versions 

788033 

Fire protection housing F30 R, wall mounting 

788034 

Fire protection housing F30 L, wall mounting 

788035 

Fire protection housing F30 R, standing 

788036 

Fire protection housing F30 L, standing 

 
 

 

Refer to product catalog fire systems for additional information. 

 
 
 
 
 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов