manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 34 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 34

Fire Alarm Control Panel IQ8Control C / M 

 

34

  

FB 798951.10.GB0 / 04.15

 

6.1.2   Mains connection and earth connections 

The control panel may only be connected to the mains by a qualified electrician and in compliance with all relevant 
standards and regulations. The corresponding connection terminals are located on the basic module. 
 

N

L1

U

X2

F1

T1.25A
H/230V~

L1

N

PE

FE

Housing mantle

terminal

Cable corss section at least 
> 4 mm² 

Main 

230V~

 

Fig. 24: Connection of the rated voltage (230 V AC) and earth connections on the basic module 

 

Requirements 

 

Use a suitable cable, e.g. NYM 3 x 1.5 mm

2

 (max. 2.5 mm

2

), or cable with the same characteristics for 

connecting the system to the mains. 

 

Connect the fire alarm control panel to the AC mains power supply via a separate mains isolator or a suitably 
rated circuit breaker. The rated voltage (e.g. 230 V AC) is specified on the FACP type plate. 

 

Use a separate FI unit if FI circuit breakers are used. 

 

Mark the fuse protection for the mains supply for the fire alarm system control panel accordingly (in red, label 
as 'FACP'). Observe national standards and guidelines! 

 

Make sure to correctly connect the protective earth (PE) and functional earth (FE). 

 

Observe local power supply provider regulations. 

 

The fire alarm control panel has been fitted with fine surge protection in accordance with EN 54 and the  
VdS guidelines. Should coarse protection be required, this must be installed by the installer for the specific 
system. 

 

 

Observe the rated voltage (e.g. 230 V AC) specifications on the FACP type plate! 

Connecting cable insulation 

The cable sheath (jacket) of all of the connecting cables must be left intact up to a point inside the 
housing and only be removed inside the housing. 

Fuses

 

The fuses of the FACP or external power supply units cannot prevent an unexpected fault in 
electrical modules; rather, these fuses are intended to protect users and their surroundings from 
damage. Fuses must therefore never be repaired or bridged or replaced with any fuses other than 
the stated type! 

Danger of damage! 

The mounting surface and mounting material must be strong enough to hold the relevant battery type 
used.  

Protective and functional earth 

For the device to function properly, the network side protective earthing (PE) connection must be 
connected to the correct terminal. The functional earth (FE) must also be connected to the protective 
earthing rail (PE rail). 

 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов