Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 57

Страница: 57 / 138

Fire Alarm Control Panel IQ8Control C / M

FB 798951.10.GB0 / 04.15

6.4.2 Connecting master box (Relay K1)

Relay K1 for the connection of a master box is part of the peripheral module.

The control configuration of relay K1 can be set to



monitored and switching the positive potential



switching the positive potential



or as a non-monitored change-over contact

by means of jumpers.

BR1

BR2

Fig. 48: Location of the master box relay K1 and the jumpers BR 6 to 8 on the Field device module

Setting the operating mode for relay K1

Jumpers

Function

BR 1

Activation of master box relay (K1) also in the event of a fire alarm with the control panel in
the CPU failure mode (factory setting)

BR 1

No activation of the master box relay (K1) in the event of CPU failure-fire

BR 2

No activation of the master box relay (K1) in the event of a fire alarm when the cover
contact on the control panel housing is open (factory setting)

BR 2

Activation of master box relay (K1) even with cover contact open (outer housing)

Содержание ESSER IQ8Control M











































































































































Результаты поиска

Содержание ESSER IQ8Control M

Отзывы:

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 57 / 138

Результаты поиска

Содержание ESSER IQ8Control M

Отзывы: