manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 92 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 92

Fire Alarm Control Panel IQ8Control C / M 

 

92

  

FB 798951.10.GB0 / 04.15

 

Inhibiting MFAB activation 

The master box or master box relay will not be activated if, 
 

 

the cover contact is open. Factory setting of solder jumper on module: BR2 = open ; BR3 = closed. The 
customer data of the FACP must be programmed under menu point Functional designation of the MFAB 
control module to suppress the activation of the master box when the cover contact is open.  

 

the operating panel keyboard has been enabled for operation (key-operated switch). 

 

the master box is disconnected. 

 

there is trouble with the master box. 

 

Activation of the MFAB in dependency on the cover contact (BR2 and BR3) 

The hardware adjustment of the activation of the MFAB is determined by the two solder bridges BR2 and BR3 on 
the MB control module. 
 
Factory setting Germany 

D

 configuration 

 

BR2 = open 

BR3 = closed 

The activation of the MFAB occurs in dependency on the customer data 
programming. If, for BR3 = closed example, activation has been suppressed in the 
menu point Functional designation of the MFAB control module when the cover 
contact is open, the master box will not be activated in the case of an event when 
the cover contact is open. 
 

 
Configuration for the Netherlands 

NL

 

 

BR2 = closed 

BR3 = open 

The activation of the MFAB occurs independently of the customer data 
programming. If, for example, activation has been suppressed in the menu point 
Functional designation of the MFAB control module when the cover contact is 
open, the master box will still be activated in the case of an event by hardware 
when the cover contact is open. 

 
 
 

9.1.1  Technical Data Master box activation module (Part No. 784385) 

Operating voltage 

:  Internal via the power supply module, + 5 V DC / +12 V DC 

Quiescent current consumption 

:  approx. 10 mA @ 12 V DC (without monitoring) 

approx. 15 mA @ 12 V DC (monitored) 

Emergency operation 

:  yes 

Fuses 

:  Multifuse 1 A  

Relay K1 

:  1 monitored change-over contact (e.g. MFAB activation) 

contact rating max. 30 V DC / 1 A 
Monitored resistance 50 to 1000 

Ω

 

Activation time (relay K1) 

  Continuously or pulsed (0,25 s / 1,5 s / 2,5 s or 6 s) 

Output "MFAB reset“ 

:  max. 300 mA (+12 V DC or +24 V DC), short-circuit proof 

 

Output "FDKB unlock" 

:  max. 300 mA short-circuit proof 

 

Compatibility 

:  The Interface modules may be operated on a free selectable 

micro module slot of the FACP IQ8Control. 

For FACP 800x the MB interface module may be used as a 
replacement devices. 

 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов