manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 105 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 105

Fire Alarm Control Panel IQ8Control C / M 

 

FB 798951.10.GB0 / 04.15

 

105

 

10.7 Printer function 

Under this menu point, the protocol printer connected to the Fire Alarm Control Panel (internal printer and/or 
external serial printer) can be switched on or off. In addition, the contents of the internal event memory of the 
control panel can be printed out on a local protocol printer. 
 

 

The activation of other control panel printers in the essernet

®

 is impossible. 

 

Internal protocol printer 

The internal protocol printer is selected with a (max.) four-digit number. This number consists of the control panel 
number (e.g. 1 to 31 in an essernet

®

) and the number "01". 

 
Example:  panel number 01 

 Nr. of the internal protocol printer 01

10 

 

panel number 05 

 Nr. of the internal protocol printer 05

10

 

 

External protocol printer 

The external protocol printer is selected by the primary loop number of the RS 232/TTY module to which the 
printer is connected. The primary loop number consists of the number of the FACP, the micro module board and 
the slot in which the RS232 / TTY-Module is fitted. 
 
 
 

Switching off the protocol printer 

By the first activation of the menu options >Printer function<, the printer number is automatically allocated to the 
internal protocol printer if installed. This allocation can be removed by pressing the >Zone< key. 
 

Func.menu

Repeat

Select

Switch off
Switch on
Print event mem

Printer

:    

Printer   

 

Fig. 94: Function menu 

 

 

Enter the number of the printer which is to be switched off (primary loop number of the serial interface) and 
press the >Select< function key 

 

Enter the number of the desired function (1 = Switching off) or select the menu options Switching off with the 
cursor keys and press the >Function< key 

 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов