manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 131 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 131

Fire Alarm Control Panel IQ8Control C / M 

 

FB 798951.10.GB0 / 04.15

 

131

 

The extension housing is assembled / mounted similar to the central housing. The individual assembly steps are 
described in the section "Assembling the central housing". 
The following must also be observed when assembling the extension housing: 
 
 

 

The connection pieces between the central and extension housings can be pushed into the housing only from 
the rear side due to the door hinge. If an extension housing is fitted at the bottom to an already securely 
installed central housing, the central housing must be removed from the assembly surface. 

 

 

A separate drilling template is available for each of the two housing variants with the standard or battery rear 
panel. The drilling template is enclosed in the central unit’s additional pack. 

 

 

The fastening holes in the mounting surface must be drilled precisely and without offset to the side. Otherwise, 
use of the connecting pieces between the two housings is no longer possible in the event of major deviations. 

 

 

If the extension housing with the battery rear panel is used, please note that depending on the 
rechargeable batteries used, a significant weight must be supported by the fastening screws of the 
extension housing. Longer 8 mm flat-head screws should always be used here. 
Each housing must be separately secured with suitable fastening materials such as screws and dowels. 
Attachment of the extension housing only via the connection pieces between the central and extension 
housing is not permissible. 

 
 
 

19.1  Extension housing for two batteries (Part No. 789300 / -01) 

Up to 2 batteries 12 V / 24 Ah may be placed inside the lower housing part of the IQ8Control M or in the extension 
housing (Part No. 789300 / -01). The required battery fastener (plastic device) is delivered with the panel 
equipment. 
 

1

2

 

 
 
 
 
 
 
 
 

 

Place batteries as shown and insert 
fastener. 

 

Assemble the additional battery mount 

 

and 

. 

Fig. 110: Mechanical battery  

 
 

 

Damage to the system!

 

Please note that depending on the rechargeable batteries used, a significant weight must be supported 
by the fastening screws of the extension housing. It is not permissible to install the rechargeable 
batteries without these fastening clamps. 

 

 

See Chapter 4.1.3. 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов