Holzstar 5904026 Скачать руководство пользователя страница 8

Страница: 8 / 58

ADH-Series | Version 1.02

Safety

2.8 General safety instructions

This machine is equipped with several safety devices
designed to protect both the operator and the machine.
However, this cannot yet cover all safety aspects and
thus the operator. Before you put the machine into ope-
ration, you must read and fully understand this chapter.
In addition, the operator must also consider other as-
pects of the hazard in relation to the environmental con-
ditions and the material

Note the following:

- Before connecting the device to the mains, make

sure that all safety elements are activated and
check their positions and function.

- If it is necessary to remove the doors or protective

covers, turn off the switch and disconnect the plug
from the outlet.

- The non-return device must move freely and its

operation must be checked regularly (several
times a day).

- Do not connect the appliance to the mains if the

door or protective cover has been removed.

- To avoid operating errors, familiarize yourself with

the location of the switches on the machine before
switching them on.

- Memorize the position of the emergency stop

switch so that you can use it immediately at any
time.

- Be careful not to touch any switches while the ma-

chine is in operation.

- Never touch a rotating tool with your hands or

other objects.

- If you are not working on the machine, switch off

the machine at the MAIN switch and disconnect
the plug from the socket.

- Before cleaning the machine, switch off the ma-

chine and unplug the machine.

- Switch off the machine before carrying out main-

tenance work on the machine and disconnect the
plugs from the machine.

- Do not modify the machine in a way that poses a

risk to safe operation.

- Carry out regular inspections in accordance with

the instructions for use.

- Check and ensure that the machine is not subject

to any malfunctions caused by the user.

- After the work is finished, adjust the machine so

that it is ready for use in another production series.

- If there is a power failure, switch the machine off

immediately.

- Do not paint, soil, damage, alter or remove the

safety plates. If they become illegible or are lost,
contact the production line and replace the plates.

- Always keep the working area clear. Overcrowded

areas and workbenches cause injury.

- Consider the surroundings of the work area. Do

not expose tools to rain. Do not use tools in damp
or wet locations.

- Keep the work area well lit.
- Do not use tools near flammable liquids or gases.
- Therefore, remove objects such as rings, watches,

bracelets, ties, etc. before starting work, as they
may get caught on different parts of the machine.

- Protect and secure your hair properly so that it

cannot be caught by moving parts on the ma-
chine.

- Wear shoes that are recommended or required by

the health and safety regulations of all countries.

- Always wear the necessary safety equipment

(safety glasses, apron, safety shoes, hearing pro-
tection, etc.).

- Wear a helmet if there are obstacles above your

head - in the work area.

- Always wear a dust mask while working on mate-

rial that generates dust during the process.

- Never wear loose work clothing.
- Do not work on the machine under the influence of

drugs or alcohol and when you are tired.

Содержание 5904026



























































Результаты поиска

Содержание 5904026

Отзывы:

Похожие инструкции для 5904026

Бренды по названию

Популярные бренды

Holzstar 5904026, Руководство по эксплуатации

Результаты поиска

Содержание 5904026

Отзывы:

Похожие инструкции для 5904026

Бренды по названию

Популярные бренды