Holzstar 5904026 Скачать руководство пользователя страница 31

Страница: 31 / 58

Troubleshooting tables

ADH-Series | Version 1.02

10.2 Troubleshooting table - Planer

Problem

Possible cause

Solution

Snipe

NOTE: Snipe can be minimized but not eliminated.

The knife is set higher
than the output table.

Align the cutting head
knives and the output
table.

(See „Setting the Cut-
ting Head Knives“)

Insufficient support of a
long board.

Support a long board
with extension rolls.

Uneven feed roller pres-
sure from front to rear.

Adjust the feed roller
tension.

Blunt knives.

Sharpen or replace the
knives.

Lumber not butted pro-
perly

Butt end to end each
piece of stock at the
pass through.

Structure is fibrous..

The wood has a high
moisture content.

Allow the wood to dry or
use a drying chamber.

Blunt knives.

Sharpen or replace the
knives/knife inserts.

Torn grain

Too heavy a cut..

Adjust proper depth of
cut

The knives cut against
the grain.

.Cut in grain direction.

Blunt knives.

Sharpen or replace the
knives

Rough / Raised Grain

Blunt knives.

Sharpen or replace the
knives

Too heavy a cut..

Adjust proper depth of
cut

Moisture content too
high.

Make sure that the
wood dries.

Rounded, glossy surface

Blunt knives.

Sharpen or replace the
knives

Feed speed too slow

Increase the speed.

Cutting depth too
shallow.

Increase the depth.

Содержание 5904026



























































Результаты поиска

Содержание 5904026

Отзывы:

Похожие инструкции для 5904026

Бренды по названию

Популярные бренды

Holzstar 5904026, Руководство по эксплуатации

Результаты поиска

Содержание 5904026

Отзывы:

Похожие инструкции для 5904026

Бренды по названию

Популярные бренды