Holzstar 5904026 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 58

background image

Safety

ADH-Series | Version 1.02

5

Operating staff:

Operating staff has undergone an induction by the ope-
rator about the entrusted tasks and potential hazards
resulting from improper behaviour. Tasks which go
beyond normal operation may only be carried out by the
operator if they are listed in the operation manual and
the operator has made him/herself familiar with them.

Qualified electrician:

Due to the electrician's specialised training, know-how,
experience and knowledge of pertinent standards and
regulations the electrician is in a position to work on the
electrical systems, and autonomously identify and avoid
potential hazards.

Specialist staff:

As a result of specialist training, expertise, experience
and skills in terms of the relevant standards and regula-
tions, specialist staff is able to complete the tasks they
are entrusted with and independently identify hazards
and avert risks.

Manufacturer:

Certain work must be carried out by manufacturer spe-
cialist staff only. Other staff is not permitted to carry out
this work. Contact our customer service to have the work
carried out.

2.4 Personal protective equipment

Personal protective equipment is intended to protect the
health and safety of persons at work. Staff must wear the
personal protective equipment indicated in individual
sections of these operating instructions when carrying
out the different tasks on the machine.

The personal protective equipment is described in the
following section:

Head protection

The industrial helmet protects the head against fal-
ling objects and bumping into stationary objects.

Hearing protection

The hearing protection protects the ears against
damages of hearing due to noise.

Eye protection

Protective glasses protect the eyes against pro-
jected parts and splashes of liquid..

Protective dust-mask

The dust protection mask protects the respiratory
tract from wood chips and wood dust.

Protective gloves

The protective gloves provide protection for the
hands against sharp-edged components, as well as
against friction, abrasions or deeper injuries.

Safety boots

The safety boots protect the feet against crushes, fall-
ing parts and slipping over on slippery underground.

Protective clothes

Protective work clothing means tight-fitting clothing
with low tear resistance.

CAUTION!

Impurged, possibly contaminated body protection
products can cause illnesses.
Clean them after each use and once a week.

«
...
3
4
5
6
7
...
»

Содержание 5904026



























































Отзывы:

Нет отзывов

Похожие инструкции для 5904026

Бренд: Denon Страницы: 147

Бренд: Marantz Страницы: 28

Бренд: Far Tools Страницы: 73

Бренд: Akai Страницы: 5

MD6447 - MD CD Player

Бренд: Memorex Страницы: 49

Бренд: Onkyo Страницы: 16

Бренд: Saba Страницы: 46

Бренд: Lenoxx Страницы: 14

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 8

PalmTheater DVD-LV55

Бренд: Panasonic Страницы: 23

PalmTheater DVD-LS5

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 33

PalmTheater DVD-LS50

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 50

Бренд: Panasonic Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды