Holzstar 5904026 Скачать руководство пользователя страница 32

Страница: 32 / 58

ADH-Series | Version 1.02

Troubleshooting tables

10.3 Mechanical Troubleshooting - Planer-Thicknesser

Poor feeding of lumber.

Uneven feed roller pres-
sure.

Adjust the feed roller
tension.

Planer bed is rough or
dirty.

Clean the incline and
remove any residue.

The transmission V-belt
slips.

Tighten the transmis-
sion V-belt.

The surface of the feed
rollers is clogged.

Clean the pitch and re-
move the residue from
the teeth.

Uneven depth of cut side to side

Knife projection

Adjust the knife protec-
tion.

Cutter head not level with
bed.

Adjust the table bed le-
vel.

Board thickness does not match depth of cut scale.

Depth of cut scale uncor-
rect

Adjust depth of cut
scale.

Problem

Possible cause

Solution

Problem

Possible cause

Solution

Chain jumping.

Inadequate tension.

Adjust the chain tension.

Sprockets misaligned

Align sprockets

Sprockets are worn.

Replace the sprockets.

Machine does not

start /

does not restart

No incoming power.

Check that the device is connected to the power supply,
the START button is pressed completely, and the STOP but-
ton is released.

The automatic overload re-
set has not restarted.

If the overload switch on the circuit breaker in the motor
starter is overloaded, it takes time for the machine to cool
down before restarting. Allow the machine to cool down suf-
ficiently before restarting.

If the problem persists, check the ampere setting on the
motor starter in the electrical box.

Содержание 5904026



























































Результаты поиска

Содержание 5904026

Отзывы:

Похожие инструкции для 5904026

Бренды по названию

Популярные бренды

Holzstar 5904026, Руководство по эксплуатации

Результаты поиска

Содержание 5904026

Отзывы:

Похожие инструкции для 5904026

Бренды по названию

Популярные бренды