Holtek HT32F50231 Скачать руководство пользователя страница 408 | Manualshive

Страница: 408 / 486

Holtek HT32F50231 Скачать руководство пользователя страница 408

Rev. 1.00

408 of 486

July 31, 2018

32-Bit Arm

®

Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

19 Inter-Integrated Circuit (I2C)

19 Inter-Integrated Circuit (I2C)

Bits

Field

Descriptions

[16]

RXDNEIE

Data Register Not Empty Interrupt Enable Bit in Received Mode

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware.

[11]

TOUTIE

Timeout Interrupt Enable Bit

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware.

[10]

BUSERRIE Bus Error Interrupt Enable Bit

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware.

[9]

RXNACKIE Received Not Acknowledge Interrupt Enable Bit

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware.

[8]

ARBLOSIE Arbitration Loss Interrupt Enable Bit in the I

2

C multi-master mode

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware.

[3]

GCSIE

General Call Slave Interrupt Enable Bit

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware.

[2]

ADRSIE

Slave Address Match Interrupt Enable Bit

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware.

[1]

STOIE

STOP Condition Detected Interrupt Enable Bit

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware. The bit is used for the I

2

C slave mode only.

[0]

STAIE

START Condition Transmit Interrupt Enable Bit

0: Interrupt is disabled

1: Interrupt is enabled

When the I2CEN bit in the I2CCR register is cleared to 0, this bit is cleared to 0 by
hardware. The bit is used for the I

2

C master mode only.

«
...
406
407
408
409
410
...
»

Содержание HT32F50231







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов